Evinrude Ignition Bulletin #1148 (February 1977)
This factory service bulletin documents step-by-step battery C.D. ignition troubleshooting, voltage requirements, amplifier and pulse pack testing, and the 1972 ignition system conversion for 1969-1970 115 HP engines.

February, 1977
TROUBLE SHOOTING BATTERY C.D. IGNITION
NOTE: This procedure must be followed in a step by step sequence.
NOTE: After a malfunctioning part or connection is replaced or corrected, immediately recheck the last test that failed. (Before trouble shooting the ignition, make sure the battery is fully charged and in good condition.)
STEP 1. Check spark at plug end of high tension leads, using 3/8" gap on needle point spark tester. If spark is good, check spark plugs. If the plugs are okay, check timing and points or sensor gap. If above is okay, ignition is okay, except pulse pack or amplifier may break down after warm-up. If spark is bad, go to step 2.
NOTE: On 1969 and 1970, 115 only, place a jumper wire between terminal 7 and 9 on the terminal board and repeat step 1. If jumper provides correct spark, check ignition safety circuit assembly, rectifier, shift diodes and stator, and replace defective part. Allow jumper to remain in place until all ignition system checks are completed and spark checks good. Then remove jumper and retest spark. If spark is not satisfactory when jumper is removed, see Step 5B. NEVER ALLOW CUSTOMER TO OPERATE ENGINE WITH JUMPER IN PLACE.
STEP 2. INPUT VOLTAGE Check wiring and battery for clean, tight and correct connections. Using a voltmeter, check input voltage at amplifier or pulse pack at time of engine malfunction. Minimum voltages are as follows:
MOTOROLA AMPLIFIER PRESTOLITE PULSE PACK Cranking speed 9.0 Volts 9.5 Volts Idle speed 12.0 Volts 12.0 Volts High speed 12.5 Volts 12.5 Volts
If voltage is okay, go to step 3.
If voltage does not meet minimum requirements, check battery, key switch, solenoids and other excessive power drains from battery including exces- sive starter motor current draw.
NOTE: Keep voltmeter connected so that pulse pack or amplifier input voltage can be observed while testing further.
STEP 3. PULSE PACK OR AMPLIFIER OUTPUT Disconnect amplifier output lead from coil primary lead. Connect S-80 or M-80 neon tester blue lead to output lead coming from amplifier or pulse pack and black tester lead to engine ground. Set switch to position 1, depress lead A and crank engine.
STEP 3. continued...
If the neon lite is showing a strong regularly flashing or pulsing lite, go to Step 4.
If lite is weak, erratic or intermittent, check points or sensor and connecting wires for grounds, opens, correct resistance and correct gap settings. If okay, replace pulse pack or amplifier.
If no lite is showing, disconnect sensor or points from pulse pack or amplifier and trigger manually (key switch on) as follows:
MOTOROLA AMPLIFIER: Tap ignition point lead coming from amplifier to ground. Each time lead is removed from ground, neon lite should flash only once. Any other result means amplifier is faulty.
PRESTOLITE PULSE PACK: Connect a test sensor and sensor rotor to sensor leads from pulse pack and spin test sensor rotor. Neon lite should flash at the same speed at which the test sensor rotor is being turned. If manual trigger does not produce the correct flash from the neon lite,
the pulse pack or amplifier is faulty and must be replaced.
COIL TEST
Remove high tension coil lead from distributor cap. Re-connect coil primary leads (-) to ground and (+) to pulse pack or amplifier. Connect coil high tension lead to a spark checker with gap set at 1/2 inch.
Crank engine.
If spark is bad, replace coil
If spark consistently jumps 1/2" gap, coil is good. Go to step 5.
DISTRIBUTOR CHECK
A. Check distributor cap, rotor and high tension spark plug leads per service manual. Caps, rotors or high tension leads are faulty if arcing occurs to or through any non-metallic surface while probing with high voltage. If all items and checks are good up to this point but engine misses, replace amplifier or pulse pack.
B. Additional information on some specific problems is found in electrical service bulletins 844, 868, 878, 879, 900, 950, 970, 971, 973, 985, 1020, 1076 and trouble shooting bulletins 829 and 837. On 1969 and 1970, 115 HP models, pay particular attention to service bulletin 1076 regarding the installation of a diode, part number 383538, to eliminate hard starting.
REPLACEMENT PULSE PACK 1969-70, 115 HP
If all the above procedures fail to eliminate a problem in the 1969 and 1970, 115 HP engines equipped with service replacement pulse packs, part number 385038, you can install a 1972 style ignition system as per Step 7. This 1972 style ignition system can also be utilized when a replacement pulse pack, part number 385038 is required.
INSTALLING 1972 PULSE PACK ON 1969-70, 115 HP
To install a 1972 style ignition system on 1969 and 1970, 115 HP engines in place of service replacement pulse pack, part number 385038, follow the procedure listed on the next page:
Install a part number 384522 phase II pulse pack with sensor rotor part number 316678.
Remove the sensor leads from the base plate assembly and install part number 385200 lead assembly on the original base plate assembly or install a new base plate assembly, part number 384547. Follow the instructions included with the assembly. Put the ground lead toward the clamp so that the sensor leads are within the channel for protection, as shown in figure 1.
Remove and discard the ignition safety circuit. Install a clipper circuit part number 580891. Refer to 1972, 125 HP engine service manual for installation instructions. Check engine timing with timing light. These modifications result in an engine with the ignition system similar to the 1972, 125 HP models.
Figure 2 shows the 1972 distributor base plate assembly on the right and the 1969 & 1970 distributor base plate on the left with lead assembly, part number 385200.

Service Department