Evinrude Service Bulletin #1257: Safety Related Considerations in Rigging and Testing a Boat and Motor
Factory service bulletin issued in 1980. Historical reproduction of the original 3-page technical document.

ENGINE MOUNTING #1257
May, 1980
Safety Related Considerations In Rigging And Testing A Boat And Motor
General
* Select products recommended by boat manufacturer or motor manufacturer which
meet design and performance requirements of the marine industry's safety standards
(A.B.Y.C.).
¢ Always follow manufacturer's Installation Instructions closely when mounting engine
and accessories.
¢ Never substitute parts specified by manufacturer. Even simple nuts and bolts may be of
special design to resist corroding or breaking.
¢ Read Safety Section, Part A & B, of the outboard motor Service Manual (50 h.p. or
larger), to see what might happen if care is not taken during rigging.
¢ Never overpower a boat. Engine’s horsepower must never be greater than that indicated
on the boat's certification plate.
Mounting of Engine
¢ Make sure boat's transom is Flat in engine mounting area. If transom is curved, use
solid aluminum wedges which contact the full mounting surface of the engine's stern
brackets. They are available from local sources. See other High Performance Bulletins.
¢ Always attach engine to boat with All the bolts. nuts, washers and support plates pro-
vided by manufacturer. Never substitute parts
e Use of Wedges and thicker transoms, may require longer mounting bolts. Optional bolts
available are P/N 313327 (4” long), P/N 326614 (42° long) and P/N 321577 (6 long).
¢ Carefully caulk around and tighten All engine mounting bolts. See engine manufac-
turer’s specifications.
Remote Control Boxes
e Use the OMC remote control box shipped with the outboard, (an OMC Accessory remote
control) or an equivalent control box with ‘neutral lock’ feature
© Determine a mounting position with ample hand clearance between control box handle
and boat structure and/or steering wheel in all handle positions.
e Attach control box using All mounting hardware provided or recommended (example:
optional spacers). Always use backing washers as specified in Installation Instructions.
Do not substitute parts.
CR 80-7 ‘<:\OUTBOARD MARINE CORPORATION 1980 ALL RIGHTS RESERVED
Remote Control Cables
* Select OMC remote cuntrol cables or cables of equivalent quality, (example: should
‘-) have sealed cable ends, lifetime lubrication, and annealed core wire ends).
¢ Determine cable length required to insure that binding does not occur in any position.
See remote control manufacturer's Installation Instructions. Never clamp cables in a
position that will cause a sharp bend (minimum radius 6") in the cable.
* When using OMC Long Life cables, be sure to follow Installation Instructions very
carefully to correctly kink both remote control cable wire ends when attaching the cas-
ing guides.
Steering Systems: (Mechanical Push/Pull Versions)
© Select steering system parts which meet requirements of current marine industry safety
standard (A.B.Y.C.; P-17).
¢ If steering helm, cables, cable anchor and connector kit are already installed in boat,
make sure the existing connector kit is the same (or equal to) the connector kit recom-
mended by engine manufacturer. Also, make sure that the steering cable is adequate
for the horsepower of the engine being installed. If existing parts are in deteriorated
condition (corroded fittings, cable jacket cut, swiveling fittings worn or binding), tell the
owner they should be replaced with current parts.
¢ Select OMC steering connector kits or kits of equal quality. See OMC Steering Connec-
tor Selection Guide or OMC Parts & Accessories Dealer Catalog for complete chart of
available OMC kits.
e Always use a dual cable steering system with dual engine installations of engines 50
h.p. and larger. Connector kits are available to attach a “parallel entry” steering system
om (both steering cables routed in parallel along same side of the boat) or an “‘opposite en-
try” steering system (cables routed along opposite sides of boat). See OMC Parts & Ac-
cessories Catalog.
¢ Dual-cable steering may also be necessary for certain high-performance single engine
installations to minimize boat instability due to endplay in some single-cable systems.
Some engines have heavy-duty lower mounts available to further stabilize the boat at
high speeds. See other High Performance Bulletins.
¢ Always attach steering system parts to the boat and the engine following the manufac-
turer’s Installation Instructions. Always use a torque wrench and tighten All fasteners
as specified. Use special care when tightening swiveling or pivoting components. They
must not bind or be restricted in their movement. Lubricate parts as specified. Do not
substitute parts.
e Never “adjust” cast parts by prying with a screwdriver to make them fit. If a part doesn’t
fit, replace it.
¢ Always determine and set the minimum trim angle of the engine by proper location of
the engine’s Angle Adjusting Rod. After adjustment, make sure Angle Adjusting Rod
Retainer is in “lock” position. See Owner's Manual of 3, 4 or 6 cylinder engines.
e Always determine trim tab position which provides best balanced steering effort.
Batteries And Electrical System
* Mount battery securely to boat hull and provide cover to shield battery cable anchor
-) points. Support cables to keep strain off attachment points.
° Inspect all wiring for correct routing away from moving parts which could cut wire in-
sulation. Use only plastic clamps to prevent cutting wire insulation.
¢ Insure fasteners are tight at all electrical connections.
¢ Insure all shields, boats and sleeves are in place over electrical connection points.
¢ Avoid abusive handling of spark plugs which might crack ceramic portion of plugs.
Fuel System
¢ Check entire fuel system for missing hose clamps, clamps not in position on fittings
and hoses not properly routed away from moving parts which could cut through hoses.
° Check system for leakage. If portable fuel system is used, squeeze fuel bulb hard until
resistance is felt and, maintaining pressure, check for leaks.
e With boats having built-in fuel tanks, anti-siphon valves, filters, etc., check the system
with fuel line vacuum tester P/N 390954 and with a fuel pump pressure gauge. See Ser-
vice Manual.
¢ If any hoses look deteriorated, tell owner they should be replaced.
Testing Boat And Motor
° Test complete rig to assure that it operates properly. Make sure:
¢ Engine cranks (starts) only when remote control handle is in Neutral position.
© When remote control handle is in Neutral, that gearcase is in Neutral gear mode.
¢ When remote control handle is in Neutral position, that the control handle’s ‘neutral
lock” engages automatically.
¢ Engine speed follows movement of remote control handle smoothly, quickly.
¢ When engine is fully tilted into boat and fully turned by the steering wheel from stop
to stop, that steering system parts do not contact any other objects in the transom
area except at the engine attachment point.
Advice To The Purchaser
¢ Instruct purchaser to read the Owner's Manual before operation (stress proper break-in
procedure).
e Advise purchaser of proper operating procedures and need for periodic lubrication and
maintenance. Use the engine Owner's Manual for reference.
¢ Encourage owner to buy a Service Manual and to retain all installation instructions
which accompanied the accessory items installed on boat.
¢ Encourage owner to make sure friends who borrow his boat have read the Owner's
Manual, and are aware of important safety related procedures and information it con-
tains.
EVINRUDE MOTORS
Service Department