Johnson Service Bulletin SB-1427 - Permanently Installed Fuel Systems

August 1976 factory recommendations for built-in fuel systems on high-horsepower Johnson outboard installations.

Johnson Service Bulletin letterhead
SB-#1427

August, 1976

SUBJECT: Permanently Installed Fuel Systems

ON MODELS: Dual V-4 or Single or Dual V-6

With the coming of larger outboard motors, we anticipate the need for information concerning permanently installed fuel systems. The following recommendations are intended as a design guide for built-in fuel systems on boats using Johnson outboard motors of more than 150 total horsepower (e.g. dual V-4 or single V-6 installations). Adhering to these recommendations will insure adequate fuel supply.

TANK PICKUP TUBE - Should be minimum 5/16" I.D. - 3/8" I.D. is preferred.

PICKUP TUBE SCREEN - Recommend stainless steel #304 wire cloth, 100 X 90 mesh, .0045 diameter wire with a total open area not less than .170 square inches.

ANTI-SIPHON VALVE - Anti-siphon valves should have a pressure drop of no more than 35 inches (maximum) of water at a fuel flow rate of 20 gallons per hour. The following OMC valves which meet the above criteria are available.

#173273 for 5/16" I.D. Hose
#173274 for 3/8" I.D. Hose
#173275 for 3/8" O.D. Copper Tube

FUEL DISTRIBUTION LINES (From Tank to Drywell Fitting) - Minimum 5/16" I.D. (3/8" I.D. preferred). OMC #319719 hose (5/16" I.D.) or OMC #123111 (3/8" I.D.) lengths. All fittings must be a minimum of 1/4" I.D. Be sure lines are free of kinks and sharp bends.

FILTER - If a fuel filter is installed, it should have no more than five inches of water pressure drop at a fuel flow rate of 20 gallons per hour. The filter should have a minimum filter area of 200 square inches. The OMC #173319 filter meets the foregoing criteria. Nipple kits #173311 (5/16" I.D.) and #173312 (3/8" I.D.) may be used to adapt filter to flexible hose. DO NOT use OMC #377381 primer kit if motors of over 150 H.P. total are installed.

FUEL LINE (From Drywell Fitting to Engine) - OMC hose primer bulb and connector assembly #173277, is available for connecting from a bulkhead fitting in the drywell to the engine.

PAGE 2     SERVICE BULLETIN #1427
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085

DUAL V-6 INSTALLATION - Two separate fuel lines, as described above, including two pick ups are recommended for a twin V-6 installation. This is also recommended as the best way to install twin V-4's. Although a single line split at the motor will work, it may be marginal under certain conditions.

GENERAL - A good pipe thread sealant should be used at all threaded connections.

IMPORTANT NOTE - We recommend that ABYC standard H-24 and BIA standard 144-75 be followed to provide a safe installation for the entire built-in fuel system. For further information review Service Bulletin #1392.

Factory diagram of permanently installed fuel system with anti-siphon valve, filter, tank, fuel distribution and primer bulb
JOHNSON OUTBOARDS

D. J. Leinonen
Technical Data Coordinator

DJL/kr

NOTE: Post on your 85 h.p. thru V-6 bulletin indexes under heading "Carburetion".

Related factory information

SB-1392 is referenced for additional built-in fuel system guidance. The bulletin also cites ABYC H-24 and BIA 144-75.

Tools, supplies and related parts

Suggested products related to this service bulletin. Verify fit and suitability before ordering.

Amazon: tools and supplies

Marine Fuel Line Assembly (3/8" Primer Bulb) & Stainless Hose Clamps

Search for these supplies on Amazon

eBay: OMC / Evinrude OEM part 173277

Search for original or compatible replacement part 173277. Check the bulletin for supersessions and model fit.

Click here to search on eBay

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.