SB-1532 - Carburetor Jet Sizes

Issued in May 1980, this Johnson Service Bulletin lists factory carburetor orifice identification numbers, sizes and replacement part numbers for outboard engines. The original two-page reference includes three orifice charts and a warning against drilling jets to reproduce factory flow.

Johnson Service Bulletin letterhead
SB-1532
May, 1980
Subject: Carburetor Jet Sizes
Models: All Outboard
Whether due to altitude or other operating conditions, it is occasionally desirable to replace carburetor orifices for improved running characteristics.
The following charts list available orifices and orifice size and part number identification. The identification number is stamped on all orifices.
Orifices (1/4 - 20 Thread Size)
Size D Type Part No. C Type Part No. (Single Barrel) (Double Barrel)
.038 38C 323150 .042 42D 322249 .045 45D 323280 45C 322664 .048 48C 323903 .049 49D 324020 49C 322221 .050 50C 324906 .051 51C 323938 .052 52D 321108 .054 54D 321407 54C 317646 .055 55D 320921 .056 56D 318684 56C 325019 .057 57D 322907 57C 317021 .058 58C 321731 .0585 58.5C 324389 .059 59D 319831 59C 317330 .060 60C 321449 .061 61D 319907 61C 320661 .062 62C 317607 .063 63C 321559 .064 64C 324776 .065 65C 322810 .067 67D 319534 67C 317183 .069 69C 319776 .070 70C 322996 .072 72C 317488 .076 76C 320502 .078 78D 319002
CR 80-4 © OUTBOARD MARINE CORPORATION 1980 ALL RIGHTS RESERVED
Orifice Plugs (5/16 - 24 Thread Size)
7.5 H.P. Through 15 H.P.
Identification Size Part Number Identification Size Part Number
35 .035 326064 36 .036 323637 38 .038 322752 40 .040 321742 50 .050 323642 51 .051 319016
54 .054 322293 58 .058 320820 60 .060 319781 66 .066 326634 68 .068 326524 70 .070 326635
Orifice Plugs (8 - 32 Thread Size)
20 .020 324005 23 .023 326188 25 .025 323003 27 .027 317474 28 .028 322936 29 .029 322776 30 .030 317473 31 .031 318823 32 .032 320016 33 .033 320015 34 .034 324025 35 .035 318832 36 .036 323703
37 .037 324698 38 .038 323149 42 .042 325829 43 .043 325828 45 .045 323151 48 .048 326500 55 .055 326928 57 .057 325869 61 .061 324977 62 .062 326856 64 .064 325837 65 .065 325836
Carburetor orifice sizes are not always equal to their stamped number size due to the effects of directional flow angles. Orifice flow is maintained at a constant when manufactured at the factory. The stamped identification number is only an indication of the size relationship of one orifice to another.
Drilling an orifice to the size denoted by identification number, does not provide the same flow as a factory made jet with the same identification number.
NOTE: Post on miscellaneous index under heading “Engine Miscellaneous.”