August 1984 revised bulletin on difficult shifting, shift lockout cam inspection, and fast idle lever repair.





Subject: Difficult Shifting Standard Equipment Remote Control
Models: All Evinrude® and Johnson® Standard Equipment Remote Controls with or without Fast Idle Lever Latch
Symptom: Looseness in the fast idle lever or motor does not return to idle RPM consistantly
Equipment, Parts Required:
| Part Number | Description |
|---|---|
| 384884 | OMC Locquic Primer |
| 384848 | OMC Screw Lock |
| 329357 | Fast Idle Lever |
| 393219 | Shift Lockout Cam |
| 325781 | Shift Lockout Lever |
| 323760 | Screw, Lockout Cam |
Solution: Inspect parts. Stake shift lockout cam screw.
Step 1. Removal and Inspection of Shift Lockout Cam and Fast Idle Lever.
⚠ 1. Disconnect battery cables before servicing electrical systems. Failure to do so could result in injury from contact with moving parts if accidental cranking or starting occurs.
122. Remove remote control from mounting location in boat. Separate cover and housing half and remove throttle cable A.
23. Remove screw B, countersunk washer C, and throttle lever assembly D from housing half.
34. Remove screw E, shift lockout cam F, shift lockout lever G, and spring washer H from housing half.
45. If the shift lockout cam does not have a slot I in the side that is countersunk for the screw head, replace it with P/N 393219. If the shift lockout cam does have a slot in the side that is countersunk for the screw head, make sure that no flash remains in the slotted area.
(Continued)
⚠ Safety Related





56. Inspect the edges of the flange J on the shift lockout cam that fits in the slot in the fast idle lever. If there is any sign of rounding of the edges, replace the shift lockout cam.
57. Inspect the slot in the fast idle lever for rounding wear. Be sure that the screw threads L in the fast idle lever are not worn. If either condition is present, replace the fast idle lever.
68. If the shift lockout lever does not have the long boss M, replace it with P/N 325781.
79. Clean any grease from surfaces of the fast idle lever and shift lockout cam. Clean threads in fast idle lever and the securing screw with OMC Locquic Primer.
Step 2. Assemble Remote Control Assembly
1. Install fast idle lever bushing and fast idle lever into housing. Install shift and throttle plate bushing into housing. Place spring washer over fast idle lever boss.
2. Install shift lockout lever and shift lockout cam. Place shift lockout cam over spring washer. Apply OMC Screw Lock to the shift lockout cam retaining screw and install the screw. Be sure to align the two ribs on the shift lockout cam with the two slots in the fast idle lever. Tighten screw to a torque of 3-4 N·m (25-35 in. lbs.). Tighten screw within torque range so the screw slots are not in line with slot in cam.
83. The fast idle lever N is not flush with the back of the housing half of the remote control. Use the fast idle lever washer O to support the fast idle lever during the staking procedure. Lay the housing half of the remote control on a flat surface with fast idle lever washer between the base of the fast idle lever and the flat surface. Figure 8 shows correct placement of washer.
94. Use center punch P to firmly stake edge of screw Q at both sides of slot in shift lockout cam. This will prevent screw from backing out. Be sure staking is at counterclockwise corner of slot to positively lock screw in position.
5. Install throttle lever spacer, throttle lever assembly and washer.
6. Secure throttle lever screw. Tighten screw to a torque of 3-4 N·m (25-35 in. lbs.).
7. Apply OMC Triple Guard™ Grease. Be sure to grease the three cover screws.
8. Install throttle cable in housing half of remote control and reassemble the two halves.
9. Reattach remote control to boat. Test your work!
Note When servicing a remote control; if the shift lockout cam attachment screw has been staked, it must be replaced. The new screw must be staked as described above.
Listings matching the part number
Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.