OMC Service Bulletin No. 2128 - Gearcase Damage Due to Freezing

This October, 1984 bulletin addresses gearcase damage due to freezing for V-4 and V-6 outboards and OMC Sea Drive models.

OMC Outboard Service Bulletin
Gearcase
No. 2128
October, 1984

Subject: Gearcase Damage Due to Freezing

Models: V-4 & V-6 Outboards, 1.6, 2.5 & 2.6 OMC Sea Drive Models

Problem: During freezing weather operation, water may freeze in the gearcase pitot tube and expand, pushing the plug out of the gearcase cavity and allowing the water to enter the gearcase. This problem occurs when the boat and motor are removed from the water and exposed to freezing temperatures. If the pitot tube fitting is connected to a speedometer or the cap is on the fitting, we recommend the following:

  • Vent the pitot tube as described under Solution.
  • Install a fitting as described under Action Required (to make venting the pitot tube easier in cold weather).

Symptom:

1. Lubricant leaking out of the pitot tube inlet hole on the front of the gearcase.

2. Speedometer not operating properly or has stopped working completely.

Action Required:

1. To replace the plug (A) in the pitot tube cavity (B), first drain the lubricant in the gearcase. Inspect the lubricant for the presence of water, metal chips, or burned odor. Water in the lubricant will give it a white milkey appearance. Overheating will give the lubricant a black color and burned odor.

2. Refer to your OMC Service Manual for the removal, installation and inspection of the gearcase components. To determine the source of the leak, perform a pressure and vacuum test to the gearcase.

3. Invert the gearcase to retrieve the plug. If the plug is not damaged, clean the plug with OMC Locquic Primer, P/N 384884. Coat the plug with OMC Ultra Lock, P/N 388517.

(Continued)

Factory figure 1
Factory figure 2
Factory figure 3
1

4. Install the plug in the pitot tube cavity using a punch and mallet. If the plug is damaged, replace with P/N 329638 plug.

5. Tap the plug in until the plug is flush with the casting surface.

6. Reassemble gearcase and perform pressure vacuum test, reinstall gearcase and fill gearcase with lubricant.

7. To prevent water from being airlocked in the pitot tube cavity, install a plastic fitting, P/N 123692, into the speedometer hose as follows:

8. Determine a convenient location where the speedometer hose can be cut and the plastic fitting can be installed so it will be accessible.

9. Cut the speedometer hose (C) with wire cutters or a knife.

10. Install one end of the fitting (D) into the speedometer hose (E).

11. Install the opposite end of the fitting into the other end of the hose (F).

12. Push both ends of the hose onto the plastic fitting securely.

If speedometer hose is not used, carefully remove the rubber plug (G) from the plastic fitting where the speedometer hose normally connected and clear pitot cavity with air pressure. Replace the rubber plug onto the plastic fitting securely.

Solution:

Note: When the motor is to be stored, instruct the customer to remove the hose from one end of the plastic fitting. This will vent the speedometer hose and the pitot tube cavity in the gearcase and allow the water to drain.

Then reinstall the speedometer hose onto the plastic fitting securely.

Factory figure 1
Factory figure 2
Factory figure 3
Factory figure 4
Factory figure 5
Factory figure 6
Factory figure 7
2

Tools, supplies and related parts

Suggested products related to this service bulletin. Verify fit and suitability before ordering.

Amazon: tools and supplies

Marine Water Pump Impeller Kit

Search for these supplies on Amazon

eBay: OMC / Evinrude OEM part 384884

Search for original or compatible replacement part 384884

Click here to search on eBay

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.