OMC Service Bulletin No. 2135: 100:1 and VRO Engine Lubrication

OMC guidance on 100:1 fuel-oil ratios, VRO lubrication, and recommended shutdown procedures for two-cycle marine engines.

OMC Outboard Service Bulletin
No. 2135 | December 1984 | Page 1 of 3

100:1 and VRO Engine Lubrication

OMC outboard oils formerly identified as “Evinrude 50/1 Lubricant” and “Johnson 50/1 Lubricant” will
now be identified as “Evinrude Outboard Lubricant” and “Johnson Outboard Lubricant.” This name
change is due to the 100:1 fuel/oil ratio recommended for some 1985 models.

An all new, partially synthetic, high performance lubricant is also now available. It will be marketed as
“Evinrude XP*High Performance Outboard Lubricant” and ‘Johnson GT*High Performance Outboard
Lubricant” and is BIA certified TC-W.

The changes to the names and types of lubricants available, the introduction of 100:1 fuel/oil ratio
motors, and the expanded number of models equipped with the VRO (variable ratio oiling) oil injection
system justify some comment and explanation.

Evinrude® and Johnson® outboards and OMC Sea Drive® units engineered to operate on leaner oil to
fuel ratios offer the boater the advantages of improved design with low-friction components, more
economical operation from lower oil consumption, less smoke, and as always, high performance,
smooth operation, long life, and true value. To help Evinrude, Johnson, and OMC® Drive Systems
dealers answer the many expected questions concerning engine lubrication, the following questions
and answers are presented.

Question: Can the earlier Evinrude 50/1 Lubricant, Johnson 50/1 Lubricant and Canadian OMC
two-cycle motor oil be used in newer motors at the recommended 100:1 ratio?

Answer: Yes, It is the improvements made in the motors through continued engine refinements

and advances in applied two-cycle lubrication technology which allow 100:1 fuel/oil
ratios when using Evinrude, Johnson, and OMC BIA certified TC-W lubricants.

Question: Can the new Evinrude Outboard Lubricant and Johnson Outboard Lubricant be used
in older motors at 100:1 ratio?

Answer: No, not at 100:1. They can be used, but only at the originally recommended ratio.

Question: | What fuel/oil ratio should be used for VRO equipped motors running on a fuel/oil
mixture in the tank?

Answer: All 40 and larger VRO equipped motors should use a 50:1 ratio fuel/oil mixture in the
tank using BIA certified TC-W oil when the VRO oil pump is not used.

* Trademark of Outboard Marine Corporation

(Continued)
OMC Outboard Service Bulletin
No. 2135 | December 1984 | Page 2 of 3

100:1 and VRO Engine Lubrication

Question: Are there any special engine lubrication recommendations for motors used for
competitive racing?

Answer: Yes. The percentage of oil in the fuel must be increased to 4%, a 25:1 fuel/oil ratio. For
VRO equipped motors such as the Johnson 3.6 GT and 2.6 GT and the Evinrude 3.6
XP and 2.6 XP, this may be accomplished by using a 50:1 fuel/oil mixture in the fuel
tank in addition to the oil supplied by the VRO. A 25:1 fuel/oil mixture in the tank
(without VRO oil injection) may also be used.

Motors operating at competitive racing power levels will benefit from the high performance protection
of Johnson GT High Performance Outboard Lubricant or Evinrude XP High Performance Outboard
Lubricant. The advantages of these custom blended lubricants are better protection at high RPM and
temperatures, and reduced carbon, piston scuffing, and ring sticking under these conditions.

Question: Can the new BIA certified TC-W Johnson GT High Performance Outboard Lubricant
and Evinrude XP High Performance Outboard Lubricant be used for normal service?

Answer: Yes. They may be used in any outboard at the manufacturer's recommended fuel/oil
ratio.

Question: Are special break-in procedures required for 100:1 fuel/oil ratio motors?

Answer: Yes. Engines with a recommended 100:1 fuel/oil ratio must be run on a 50:1 fuel/oil
mixture in the fuel tank using a BIA certified TC-W lubricant during the break-in
period. Follow the “Fuel Mixture During Break-in” and “Break-in Procedure”
instructions detailed in the Owner’s/Operator’s Manual.

Question: Are there any special break-in procedures for VRO equipped motors?

Answer: Yes. All VRO equipped motors must be run on a 50:1 fuel/oil mixture in the fuel tank
during the first ten hours of operation using a BIA certified TC-W lubricant. This is in
addition to the oil supplied by the VRO oil injection system. At the end of the break-in
period, check the oil level in the VRO tank to verify that oil is being delivered to the
motor before switching to straight gasoline in the fuel tank.

Question: Are all 50:1 oils BIA certified?

Answer: No There are oils sold as “50:1 oil” that are not BIA certified. These oils are not
suitable for use as substitutes for BIA certified TC-W oils.

Question: | Can the new 100:1 ratio motors be run on non-certified two-cycle lubricant?

Answer: Yes, but only under emergency conditions. If only non-certified two-cycle lubricant is
available, it may be used; if the break-in procedures have been completed, and if the
lubricant is mixed at a 50:1 fuel/oil ratio. BIA certified TC-W lubricant must be used
for the break-in period. The 100:1 fuel/oil ratio is only approved for BIA certified
TC-W lubricants. Use of non-certified oils should be restricted to emergencies only,
even at 50:1. Continued use may cause serious engine damage.

(Continued)
OMC Outboard Service Bulletin
No. 2135 | December 1984 | Page 3 of 3

100:1 and VRO Engine Lubrication

Question: Are there any other special considerations related to the higher fuel/oil ratios?
Answer: Yes. Because less oil is used in 100:1 ratio motors, and in VRO and Economixer
a) equipped motors at idle, there is also less oil on the cylinder walls when the motors

are stopped.

We are now recommending a new “PROTECTIVE SHUT-DOWN PROCEDURE” for
these motors for short periods of non-use.

Protective Shut-Down Procedure: For motors operating on a 100:1 fuel/oil ratio, and for
VRO and Economixer equipped motors that operate at low power settings or neutral
before shut-down, and will not be used for more than a few days:

1. Run motor at approximately 1500 RPM.
2. Prime (or choke) motor until heavy smoke appears at exhaust or motor stops.
3. Stop motor.

For small non-VRO motors that may be stored horizontally, the fuel should be shut off or the fuel line
disconnected before priming (or choking) to lower the fuel level in the carburetor.

Do not disconnect the fuel line on VRO equipped motors during “PROTECTIVE SHUT-DOWN
PROCEDURES”. Disconecting the fuel line will affect the fuel/oil ratio of fuel supplied to the
carburetors, causing hard starting.

Note

The additional oil on the cylinder walls will protect the motor during short periods of non-use.

a) For longer periods of storage, the regular “Off Season Storage” procedures should be used.

CR 84-144