OMC Service Bulletin No. 2193: High Altitude Modifications

September 1987 OMC fuel system bulletin for CS through CU 4 HP through 3.6 GT/XP outboards, covering high-altitude orifice changes and original factory altitude charts.

OMC Outboard Service Bulletin
Fuel System

No. 2193
September, 1987

Subject:High Altitude Modifications
Models:CS thru CU, 4 thru 3.6 GT/XP

Although your dealership may not be located at or above 3000 feet above sea level, you should be aware of the modifications that need to be made to a motor when it is used at high altitudes. This will enable you to assist your customers who travel to high altitude locations to use their motor.

This bulletin is intended as a brief outline covering the following subjects:

Note Be sure the customer knows the original orifices and propeller must be installed when the motor is returned to a lower altitude. Failure to do so may result in permanent powerhead damage due to a lean running condition or engine overspeeding.

High Altitude Performance Kit

You are encouraged to order OMC High Altitude Performance Kit P/N 393533 to indicate that your customer's motor has been modified and thereby reduce accidental engine damage. The kit contains the following items:

High Altitude Requirements and Modifications:

When a motor is operated at or above 3000 feet or higher, its power output is reduced due to air density. The higher the altitude the greater the reduction in air density and the greater the power loss. In addition a further loss of power is caused by the fuel/air ratio becoming overrich due to the reduced air density. The power loss results in a corresponding loss in RPM and performance.

Although there is no way to restore sea level performance at altitude without supercharging, it is possible to regain some of the lost power and fuel economy and improve running quality by changing orifices as recommended on the Altitude Orifice Charts.

In some cases the low speed and intermediate orifices must be changed along with high speed orifices to recover good idle quality and correct acceleration problems.

It may also be necessary to replace the propeller with one of less pitch to obtain the recommended full throttle RPM. The orifice changes and repropping are equally important to obtain optimum performance at higher altitudes.

Due to the variation in boats, motor installations and operating conditions it is impossible to give exact orifice and propeller recommendations. To obtain the best performance, a technician must install the high altitude orifices and the boat would have to be water tested under actual operating conditions.

To prevent powerhead damage due to a lean running condition install the orifices and propeller for the lowest altitude at which the boat is operated.

Orifice Identification:

An identification number is stamped on all orifices. Some orifices have a letter stamped after the number that designates the type of orifice. There are four types of orifices used on current motors:

8-32 Thread Size M Type - This orifice has recently been designated as an “M type.” Previous charts and publications refer to this orifice only as an “8-32 thread” size. It has been used as a low speed, intermediate, pullover, and more recently, as a high speed orifice.

5/16-24 N Type - This type orifice is used as a high speed orifice on small motors.

1/4-20 C Type - This orifice is primarily used as a high speed orifice on double venturi carburetors.

1/4-20 D Type - This orifice is used primarily as a high speed orifice on single venturi carburetors.

Note Although C type and D type orifices appear to be identical they must not be interchanged. Orifices are machined differently for opposite fuel flow direction. Use of the wrong type orifice may result in powerhead damage due to a lean fuel mixture.

Note Drilling an orifice to the size of the identification number does not provide the same flow as a factory made orifice and may cause powerhead damage due to a lean fuel mixture.

Original OMC High Altitude Modifications factory page 3 of 8
Original OMC High Altitude Modifications factory page 4 of 8
Original OMC High Altitude Modifications factory page 5 of 8
Original OMC High Altitude Modifications factory page 6 of 8
Original OMC High Altitude Modifications factory page 7 of 8
Original OMC High Altitude Modifications factory page 8 of 8

Related marine products

eBay: OMC / Evinrude part 393533

Listings matching the part number

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.