OMC Service Letter No. 53, August, 1985. Gasoline, Lead, and Alcohol.

Many of you are aware that the U.S. Environmental Protection Agency has issued rules which have resulted in a reduction of lead in leaded gasoline from the formerly allowable 1.1 grams (.8 in California) per gallon to 0.5 gram beginning July 1, 1985. These same rules call for a further reduction to 0.1 gram per gallon beginning January 1, 1986. For the boater, lead has provided two benefits:
1. It provides a gasoline with a higher octane number than an equivalent gasoline without lead. This in turn has allowed the development of engines with higher output per cubic inch displacement.
2. It acts as a lubricant for certain internal engine components. This reduces friction, lowers temperatures, and generally extends engine life.
There are several ways to restore the octane lost by the removal of lead. One is by additional refining to create gasolines such as premium unleaded. A second, and generally more economical way, is to blend alcohol with the gasoline.
With regard to the second benefit of lead, we are not aware of any refiners having developed an acceptable additive to provide the lubrication qualities lost when lead is removed. As a result, those engines requiring lead’s lubrication may experience more rapid wear than normal. Whether or not more rapid wear occurs is dependent on the type of use the engine sees. Generally, the more severe the service, the more rapidly wear will occur.
Blends of alcohol and unleaded regular gasoline have been on the market at least since the early 1970's. In recent years, alcohol has been locally blended with unleaded premium, leaded regular, and diesel fuel. With the reduction in allowable lead, we expect more refiners, in more areas of the country, to begin blending alcohol with their gasolines.
OMC has had in effect an extensive testing program for various alcohol blended gasolines. While testing is not yet complete, results so far point to several areas of concern:
1. PERMEATION: Alcohol blended gasolines tend to slowly permeate (or pass through) nonmetallic fuel system parts. This phenomenon is similar to air gradually leaking out of a balloon or tire. During this permeation process, the alcohol removes with it some of the molecules in the nonmetallic fuel system parts. In effect, the alcohol has changed the material. The visual results can be premature hardening, surface checking (crazing) and cracking of once flexible items. In some cases, the part will swell and get mushy. The speed at which this occurs is dependent on the type and percentage of alcohol and the material composition of the part.
USERS OF ALCOHOL BLENDED FUELS SHOULD FREQUENTLY CHECK NONMETALLIC PARTS FOR SIGNS OF DETERIORATION AND REPLACE THEM WHENEVER NECESSARY.
2. WATER ABSORPTION: Alcohols will normally stay in solution with gasoline. However, alcohols also attract and hold moisture. If the amount of moisture reaches a certain level, the alcohol/water combination will separate from the gasoline and settle to the bottom of the tank. The occurrence of this event, called phase separation, is affected by the type and percentage of alcohol, local temperatures and relative humidity. Phase separation can cause several problems:
a. The alcohol/water combination can attack the inner surface of metal fuel tanks and cause corrosion. The corrosion products will eventually clog fuel filters and small passages. In time, the tank could corrode through allowing fuel leakage. The alcohol/water combination can also attack aluminum and brass in carburetors and fuel pumps with similar clogging problems.
b. In a two-cycle engine using a gasoline/oil mix, the separated alcohol/water will not contain any lubricant. Should the engine be run on this mixture, the engine may be damaged. Typical problems due to lack of lubricant are scuffed pistons and failed powerhead bearings.
c. In a four-cycle engine or two-cycle with separate oiling, the alcohol/water will be drawn into the engine where it will burn although at a leaner fuel/air ratio than normal. This leanness may cause performance problems such as difficult starting, rough idle and stalling, and piston damage due to preignition.
USERS OF ALCOHOL BLENDED FUELS SHOULD INSPECT THEIR FUEL TANKS AT LEAST ANNUALLY AND REPLACE THEM WHEN CORROSION OR LEAKAGE IS EVIDENT. Those in high humidity areas or where morning dew is a frequent occurrence should be especially alert to this problem.
3. SOLVENCY: Alcohols can act as a cleaning solvent. With older units where fuel residue buildup has occurred, this cleaning action can remove the deposit and move it along to filters and small passages where it may clog. Again, the effect is dependent on the type and percentage of alcohol in gasoline.
USERS OF ALCOHOL BLENDED GASOLINES SHOULD INSPECT FILTERS AT FREQUENT INTERVALS AND CLEAN OR CHANGE THEM WHENEVER EVIDENCE OF CLOGGING IS FOUND.
4. LEANER AIR/FUEL RATIO: Alcohol contains less energy per gallon than gasoline. As a result, alcohol blended gasolines burn leaner than straight gasoline. The greater the percentage of alcohol, the leaner the air/fuel ratio. Some indications of a lean mixture are hard starting and lower speed stalls. Some engines are more severely affected by a leaning of the air/fuel ratio.
USERS OF ALCOHOL BLENDED GASOLINES WHO EXPERIENCE LEAN BURN SYMPTOMS SHOULD CONSIDER INSTALLING LARGER DIAMETER ORIFICE PLUGS. These will generally restore the original air/fuel ratio but at some increase in fuel consumption.
Part of OMC’s test program has been an evaluation of new materials whose makers claim they eliminate the adverse effects of alcohol blended gasolines without creating other problems. If evaluation shows these claims to be true, then these materials will be incorporated into new OMC products. Also, dealers will be notified of the availability of these replacement parts so that they might be recommended to owners of older units where appropriate.
CR85-59
Related products
Service supplies and replacement parts - recommendations coming soon.