OMC Service Letter Booklet - No. 29

This four-page factory booklet combines voltage-regulator shielding instructions, a 1986 OMC Tracker warranty and troubleshooting letter marked No. 28 Rev. 2, and an earlier electric-motor warranty letter marked No. 29 from 1983. The original factory headings, dates and numbering are retained.

Shielding the Voltage RegulatorNo. 29

Voltage regulators will sound much the same as ignition noise, varying with engine RPM. However, when the ammeter indicates full charge, the noise will not be heard. As the ammeter “cuts-back” to reduced charge, the noise will begin. Loading the battery by using lights, motors, etc. will cause the charging system to function. Turn off these loads, and when the battery is fully charged the charge rate will “cut-back” giving you a chance to verify the noise source.

Install a .5 MFD by-pass capacitor (J) to the B+ (purple) lead (K) of the voltage regulator. Solder capacitor lead (L) to the B+ lead of voltage regulator (tape to protect from moisture). Install the capacitor on the regulator (M) if possible. Add a shake proof type washer (N) between the bracket of the capacitor and the voltage regulator for a good ground connection. Clean engine ground where voltage regulator mounts to engine.

Voltage regulator shielding illustration showing capacitor J, lead K, solder connection L, regulator M and washer N
29
16
Original OMC Service logo
Service Letter
Warranty Information
No. 28 Rev. 2
February, 1986

Subject:   OMC Tracker® Warranty/Service Policy

Please Read and Retain the Following Information for Reference.

The OMC Tracker will be warranted and serviced in the following manner. OMC Tracker Fishfinders are warranted for one year (six months if used commercially) from date of original purchase against defects in material or workmanship.

Warranty Service

  1. Retail customer to provide proof of purchase (copy of sales slip) to establish warranty eligibility.
  2. Check installation of unit to be sure that problem is not in transducer or power supply. (See enclosed troubleshooting information.)
  3. If the OMC Tracker is faulty, it must be returned by the owner or dealer to OMC Trade Winds for service.
  4. Carefully package the unit (in original carton if possible) along with an OMC Warranty Claim or the OMC Tracker Return Form located in the back of the OMC Tracker Owner’s/Operator’s Manual. Information required on the Warranty Claim or OMC Tracker Return Form includes:
    1. Dealership name, address and dealer code number
    2. Customer’s name and address
    3. Selling dealer’s name and address
    4. Model and Serial Number of OMC Tracker (Some units do not have a serial number.)
    5. Date of purchase
    6. Complete details of problem with the unit.
  5. Ship the OMC Tracker and the Warranty claim or OMC Tracker Return Form prepaid to:
    OMC Trade Winds
    1211 Depot Street
    Manawa, WI 54949
    Attn: OMC Tracker Repair Department

The OMC Tracker does not have any serviceable components inside. Do not open the unit. Warranty may be voided if the OMC Tracker has been disassembled.

Within five (5) working days of receipt at Trade Winds, the OMC Tracker unit will be repaired and returned to you freight prepaid.

Out of Warranty Service

For all Out of Warranty repairs, there is a minimum charge of $35.00. A check in this amount must accompany the OMC Tracker when it is returned. Follow the return procedure as noted in number 5 above. Within five (5) working days of receipt at Trade Winds, the unit will be repaired and returned to you freight prepaid.

If a returned unit is badly damaged due to accident or obvious misuse, OMC Trade Winds will contact the dealer or customer concerning the details of necessary repairs and the cost. The dealer or customer will have 30 days to submit this check (payable to OMC Tracker Service) to OMC Trade Winds or the unit will be returned unrepaired.

Inquiries or Correspondence

Do NOT direct your inquiries to OMC Trade Winds. Inquiries regarding a returned unit, warranty, troubleshooting or servicing should be directed to:

Outboard Marine Corporation
Service Department
3145 Central Ave.
Waukegan, IL 60085
Telephone: 312/689-6290

Troubleshooting Information

Power Source Checklist

A. Check battery connections for corrosion, looseness, and correct polarity.
B. Do not connect to electric trolling motor battery.
C. Battery output below 11.0 volts measured at the OMC Tracker power cord, may cause erratic readings.
D. If OMC Tracker readings are erratic only at times, check for other electrical interference such as bilge pumps or aerator pumps.

Transducer Checklist

A. Mounting screws must be tight.

B. Angle between transducer face and water surface should not exceed 5 degrees in any direction.

C. There should be no obstructions (strakes, thru-hull fittings, rivet heads, marine growth, etc.) ahead of transducer which could cause water turbulence or air bubbles.

D. Bottom face of transducer must be in full contact with water at all boat speeds.

E. Extension cord (if used) must have a good connection at each end fitting.

F. Make certain bottom face of transducer is clean and free of marine growth, fuel, oil, calcium residue, road tar, etc. Remove marine growth (while wet) with scraper. Use scraper VERY CAREFULLY to avoid gouging plastic surface. Remove oil film with mild detergent and scrub brush. Fine grit sandpaper on a flat block can be used to clean bottom face and restore a “like-new” surface finish.

G. Check for damage from trailering or striking underwater objects. (Deep scratches in bottom face can cause air bubbles resulting in erratic readings.)

H. After boat has been out of the water for a period of time, it may be necessary to wash bottom face with mild detergent (or rub with hand after re-entry into water) to remove adhering air bubbles so that normal operation may be obtained immediately.

I. If OMC Tracker readings are erratic or absent while boat is stationary in water (and transducer bottom face has been painted with anti-fouling paint), remove paint with fine grit sandpaper on a flat block and check for improved readings.

J. Use 9 degree transducer on planing boats only. Use 18 degree transducer on electric motors or on nonplaning boats in water less than 60 feet. For additional assistance, contact the Service Department.

Original OMC Service logo
Service Letter
Warranty Information
No. 29
March, 1983 – Reprinted 10/83

Subject:   Electric Motor Warranty

When submitting a warranty claim for replacement of starter motors, power trim and tilt motors, or electric trolling motor assemblies, it is mandatory that the motor assembly be returned with the warranty claim. This is necessary to obtain warranty credit for these items.

Should a warranty claim be received without the motor, it will be returned to you causing a delay in warranty payment for the repair.

The warranty claim and motor should be returned collect via UPS or Parcel Post to:

Outboard Marine Corporation
Product Warranty Department
3145 Central Ave.
Waukegan, IL    60085

Related marine products

Amazon: Marine hull cleaning supplies

Related marine supplies

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.