OMC Service Bulletin No. 2297 - Servicing Deutsch Connectors

Issued in August 1995, this electrical service bulletin describes disconnection, terminal removal, installation, and crimping procedures for Deutsch connectors used on 1996 (ED) and newer OMC Modular Wiring System harnesses. It includes connector component numbers and identifies two factory service tools: OMC Connector Service Tool 342667 and OMC Hand Crimper 322696.

OMC Outboard Service Bulletin
Electrical

No. 2297
August, 1995

Subject:
Servicing Deutsch® Connectors
Models:
1996 (ED) and Newer

The Deutsch connectors used on the OMC® Modular Wiring System harnesses are waterproof and very reliable. The connectors are UV stabilized, have silicone elastomer seals around the wires, and have a serviceable lip seal between the connector halves. The crimped-on terminals grip both the wire strands and the wire insulation and require no solder.

Note The Deutsch pin and socket terminals ARE NOT the same size as Amphenol® pin and socket terminals. They CANNOT be interchanged.

Procedure:
Disconnect

Press latch - pull connectors apart.

Connect
1Check that seal Ⓐ is in place. Clean off old grease and dirt from connectors. Apply light coat of OMC Electrical Grease to seal. Push connectors together until latched.
Terminal Removal
2Use hook-end of OMC Connector Service Tool, P/N 342667, to pull out wedge Ⓑ from receptacle, or use other end of tool to pry out wedge Ⓒ from plug. Use needle nose pliers to remove wedge from 3-pin receptacle.
3Release terminal latch Ⓓ or Ⓔ, pull gently on wire.
Figure 1 connector sealFigure 2 connector wedgesFigure 3 terminal latch

Terminal Installation

Push terminal through seal until it clicks in place. Twist and tug wire if no click is heard.

4Fill connector with OMC Electrical Grease to 1/32 in. (0,8 mm) below ledge Ⓕ or end of plug Ⓖ.

Push wedge in until latched. Wedge in 2-pin receptacle is not symmetrical; position latch shoulders next to terminals.

Crimping New Terminals Onto Wire

Strip wire insulation back 3/16 in. (5 mm).

5Use OMC Crimping Pliers, P/N 322696. Place terminal in “1/8” notch of crimper for 18 ga. wire. Position ends of wire strands Ⓗ in terminal past wire crimp area Ⓘ, and position end of insulation Ⓙ past insulation crimp area Ⓚ.

Capture all wire strands in crimp - leave no loose strands. Crimp wire securely. Do not solder. Crimp insulation in “14-16” notch of crimper.

Deutsch ComponentOMC
P/N
Pin Terminal514679
Socket Terminal514680
Sealing Plug514690
Connector Service Tool342667
Hand Crimper322696
OMC Electrical Grease - 4 oz Tube
- 30 cc Syringe
504824
503243
Connector Repair Kit507197
Figure 4 connector wedge and sealFigure 5 crimping dimensions
Number
of Wires
Plug
Connector *
Plug
Wedge
SealReceptacle
Connector
Receptacle
Wedge
2176295127287514788514696514697
3514685514681514789514686514682
4176529127484514796176509127468
6514687514683514790514688514684
8176296127288514791176299127292

* Plug connector includes seal.

Related products

Complete Deutsch connector repair kit with tools - recommendations coming soon.

Related marine products

eBay: OMC / Evinrude part 342667

Listings matching the part number

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.