OMC Service Bulletin No. 2320: U.S. EPA Emission Information

October 1997 bulletin on U.S. EPA emission regulations and engine family labeling for 1998 (EC) and newer gas outboards.

OMC Technical Service Bulletin
ROUTE TO: □ SERVICE MANAGER  □ SERVICE WRITER  □ TECHNICIAN 1  □ TECHNICIAN 2  □ TECHNICIAN 3  □ FILE
Shop Information
No. 2320
October, 1997
Subject:U.S. EPA Emission Information
Models:1998 (EC) and Newer Gas Outboards

On October 31, 1994, the U.S. Environmental Protection Agency (EPA) proposed regulations under the Federal Clean Air Act to reduce the emissions of gas outboards. The EPA Final Rule became law on October 4, 1996, affecting outboards beginning with the 1998 model year. The regulations are focused on reducing hydrocarbon and nitrogen oxide emissions.

Manufacturer Responsibilities

The majority of the EPA marine regulation obligates engine manufacturers to reduce total emissions by incorporating new technologies. The emissions level of each manufacturer’s product line must be reduced by 8.3% per year for the next nine years, achieving a 75% reduction by model year 2006.

For compliance purposes, the EPA regulation classifies carbureted 2-stroke outboards as Existing Technology. It classifies 4-stroke and FFI™ outboards as New Technology. This division encourages manufacturers to concentrate on rolling out New Technology outboards to meet the increasingly stringent emission levels.

The product line is further divided into engine families. All outboards in an Engine Family must have emission levels at or below the Family Emission Limit (FEL).

Engines in families share these characteristics:
  Number of cylinders
  In-line or V configuration
  Fuel system type
  2-stroke or 4-stroke technology

Family Emission Limits:
  Are used for determining emission compliance
  Are based on the worst emitter in the family
  Consider production variations
  Consider product deterioration over 10 years or 350 operating hours

The manufacturer must provide accurate service, maintenance, and operating information to dealers, technicians, and customers. This information will ensure that emission levels do not exceed certified limits during the engine’s life. Each outboard must be serviced and maintained in strict accordance with published technical information.

(Continued)

Dealer and Owner Responsibilities

The regulation does not require in-field emission testing, but it does obligate the servicing dealer and the engine owner to participate in maintaining certified emission levels. The regulation imposes significant financial penalties on any person found to have removed or rendered inoperative emission devices or design elements of an emission-certified engine. Penalties can also be imposed for tampering or alterations that cause the engine to exceed certified emission levels.

Some procedures that were not recommended, but commonly performed in the past, could now subject the dealership, technician, or engine owner to significant financial penalties.

Some examples are:

Installing different carburetors
Altering carburetors by changing orifices or altering calibration passages
Altering cylinder port shape or location
Altering cylinder heads to change compression
Changing ignition idle or WOT timing

It is now more important than ever to refer to the correct year and model OMC Service Manual when performing service procedures. The service manual will list service procedures and specifications that maintain emission compliance.

Emission Control Label

An emission control label will appear on all 1998 and newer gas outboards. The label identifies Engine Family information used for EPA certification.

OMC Outboard Marine Corporation
Emission Control Information
This engine conforms to model year 1998 U.S. EPA regulations for marine SI engines. This engine is certified to operate on gasoline.
Engine Family: W1PXM0158220  FELs: 160.44 g/kw-hr
Oil: TC-W3  Engine Displ: 158.1 in3
Exhaust Emission Control System: EM
Fuel: Unleaded Automotive Gasoline >87 (R+M)/2 Octane
Spark Plug: QL78YC  Gap: 0.030 in.  Idle RPM: 650 +/- 50
WOT timing: 20 +/- 1 DEG BTDC  Idle timing: 6 +/- 2 DEG ATDC

Engine Family:

W
Model Year
W=1998
1PX
Manufacturer
1PX=OMC
M
M=Marine
0158
Displacement
Cubic Inches
2
Application
1=PWC
2=Outboard
2
Technology
1=Existing
2=New
0
Manufacturer Specification

Exhaust Control System:

EM stands for Engine Modification.

Tools, supplies and related parts

Suggested products related to this service bulletin. Verify fit and suitability before ordering.

Amazon: tools and supplies

Marine Outboard Service Tool Kit / Shop Towels

Search for these supplies on Amazon

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.