← Back to 1970s OMC service bulletins

Evinrude Lower Unit Service Bulletin #1023 - Gearcase Safety Shifting Test

September 1973 safety test program for 1973 50 through 135 HP models manufactured before January 1, 1973. The bulletin includes dealer test procedures, RPM settings, repair part numbers and four original instructional figures.

Evinrude Service Bulletin letterhead
LOWER UNIT #1023
September, 1973
TEST PROGRAM FOR ALL 1973 50 THRU 135 HP MODELS MANUFACTURED PRIOR TO JANUARY 1, 1973
Safety warning
Recently, all selling dealers of the above subject models were notified by Service Letter No. 109 advising of the test program. The purpose of this bulletin is to notify the non-selling Evinrude dealers of the program and also to serve as a reminder to the selling dealers.
We wish to solicit the cooperation of all our servicing dealers who have the capability to disassemble and repair the above subject model gearcases should one of these units fail the test.
Those dealers who are requested and have the capability to make the above tests may contact the Evinrude Service Department so that we can forward to you the tools required to make the test on the 50 HP and V-4 models.
EVINRUDE MOTORS Service Department
Enclosures: Service Letter 109 Owner Letter Instruction Sheets
OUTBOARD GEARCASE SAFETY SHIFTING TEST INSTRUCTIONS FOR 1973 50 - 135 H.P. OUTBOARDS
NOTE: If there are any questions concerning this test either about procedures, repairs, parts, claims or other difficulties contact: Evinrude Motors Attention: Service Department 4143 N. 27th Street Milwaukee, Wisconsin 53201
1. Fill out shifting test special claim form: Servicing Dealer Information. 2. Use only OMC 13 x 19 aluminum propeller, part number 382765. No other propeller may be used. 3. Tie boat securely at both ends to a secure dock, or mount motor securely in test tank and hook up electric and shift cables. Be sure tilt lever is in a "lock" or "run" position. 4. Start engine and warm up a minimum of three minutes in neutral and stop engine. 5. Remove motor cover. Remove cable retainer, lower motor cover cable clamp (50 H. P.) or rubber grommet (65 & V-4's). Remove spring clip and completely remove throttle cable from engine. 6. On 50 H.P. engines thread large hex cap on idle speed adjustment screw until tight. See Figure 1. On 65 H.P. engines no cap is required on idle speed adjustment screw. See Figure 2. On 85, 115 and 135 H.P. engines install the small cap on the idle speed screw over the regular black plastic cap and return spark advance lever to idle to hold cap in place. See Figure 3.
7. Start engine, shift motor to forward gear and adjust engine idle screw to the following RPMs: 50 H.P. - 1400 - 1450 RPM 65 H.P. - 1275 - 1325 RPM 85/115 H.P. - 1075 - 1125 RPM 135 H.P. - 1000 - 1050 RPM
NOTE: Check engine RPM with boat tachometer or shop tach and recheck to see that RPM has stabilized within RPM range above. Replace motor cover.
8. Shift motor through 25 complete cycles (F-N-R-N-F-etc.) without hesitating in neutral or either gear position. The 25 shifting cycles must be completed as rapidly as possible, 20 seconds maximum total time. 9. At completion of 25 shifting cycles, leave shift lever in forward gear and check to see that gearcase is actually in forward gear.
(over)
10. Stop engine in forward gear. Record shift test results on special claim form: Tested and No Failures, or, Unit Failed During Test. 11. Remove motor cover. Remove idle screw test cap and adjust idle speed as follows: 50 H.P.: 700 RPM maximum in reverse gear. 65 H.P.: 1000-1100 RPM in neutral. 85/115/135 H.P.: 650 RPM maximum in gear. Reinstall throttle cable. Remove 13 x 19 testing propeller and install customer's propeller if it was removed.
IF MOTOR PASSED SHIFTING TEST:
12. If motor passed shifting test without malfunction, start the motor and check for correct operation of shift, throttle, etc., and adjust as required. Refer to Service Bulletin Fuel System #1019. Winterize motor if it was winterized before test. Clean motor and control and replace motor cover. 13. Put three identifying marks on the top trailing edge of the gearcase with a center punch as shown in Figure 4. 14. Return motor to customer and have him sign shifting test special claim form.
IF MOTOR DID NOT PASS SHIFTING TEST:
15. If the motor malfunctioned during this test and failed to continue shifting or did not return to forward gear at the completion of the test, repair the gearcase according to approved Evinrude procedures as detailed in the appropriate outboard motor service manual, Section VI. 16. Fill in shifting test special claim form: Parts Used and Flat Rate Time. 17. After gearcase repairs have been completed, repeat complete test Items 1 through 14 above.
List of parts required to repair gearcase if malfunction occurs:
386592 - Shift Rod and Bearing Assembly (50 & 65 H.P. engines) 386593 - Shift Rod and Bearing Assembly (85, 115 & 135 H.P. engines) 313446 - O-Ring-Prop. Shaft Bearing Housing (All engines) 316564 (Four Required) - Screw-Prop. Shaft Bearing Housing (50 & 65 H.P.) 316563 (Four Required) - Screw-Prop. Shaft Bearing Housing (85, 115, & 135 H.P.) 314502 - Cotter Pin - Propeller Nut (All engines) 314082 - Gasket - Solenoid Cover (50 & 65 H.P. engines) 314876 - Gasket - Solenoid Cover (85, 115 & 135 H.P. engines)
Factory figures 1 to 4 showing idle screw caps for 50 HP, 65 HP and V-4 engines and punch identification marks on the gearcase

Tools, supplies and related parts

Suggested products related to this service bulletin. Verify fit and suitability before ordering.

Amazon: tools and supplies

Marine Lower Unit Gear Oil Pump & Seal Puller Tool

Search for these supplies on Amazon

eBay: OMC / Evinrude OEM part 382765

Search for original or compatible replacement part 382765. Check the bulletin for supersessions and model fit.

Click here to search on eBay

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.