| FUEL SYSTEM AND LUBRICATION |
| Bulletin
# |
Subject |
Date |
| Johnson 1232 |
Improving idle
characteristics on 1970 - 3 cyl. |
1/70 |
| Johnson 1242 |
Adjusting slow
speed needles on 1970 - 3 cyl. & V-4 |
8/70 |
| Johnson 1255 |
Orifice plugs and
inlet needles for 1963 thru 1971 models |
2/71 |
| Johnson 1260 |
Minimum
recommended fuel pump pressures |
4/71 |
| Johnson 1265 |
Causes of poor
idle on 1971 - 50 |
7/71 |
| Johnson 1283 |
Improve high
speed - Orifice change on 1972 - 65 |
2/72 |
| Johnson 1298 |
Replace air
silencer screws when base removed on 50 thru 125 |
6/72 |
| Johnson 1311 |
Orifice plugs
& float valve & seat for 1972 & 73 - 6 thru 135 |
12/72 |
| Johnson 1322 |
Poor idle or hard
starting characteristics on 1973 - V-4's |
7/73 |
| Evinrude 1019 | 1973 V-4 engines with poor idle or hard starting characteristics | 8/73 |
| Johnson 1328 |
Low speed knob
grommet restricting air flow on 1974 - 9.9 & 15 |
10/73 |
| Johnson 1330 |
Change in
carburetor choke valves on 1974 - 2, 9.9 & 15 |
11/73 |
| Evinrude 1026 | Change in carburetor choke valves on 1974 and 2, 9.9 & 15 hp models | 11/73 |
| Evinrude 1029 | Low speed knob grommet restricting air flow on 1974 9.9 & 15 hp models | 11/73 |
| Johnson 1331 Rev.
1 |
New idle
adjustment stop on 1974 - 9.9 & 15 |
1/74 |
| Evinrude 1032 | Engine fuel recommendations for all models | 1/74 |
| Johnson 1336 |
Spark plug
fouling on 1974 - 9.9 & 15 |
2/74 |
| Evinrude 1038 | Warm-up choke 50 - 135 hp models | 2/74 |
| Evinrude 1040 | New idle adjustment stop for 1974 9.9 and 15 hp models | 3/74 |
| Johnson 1342 |
Piston failures
on 1973 & 74 - 135 |
5/74 |
| Johnson 1354 |
Testing fuel pump
pressure on 1974 to date - 4 thru 25 |
9/74 |
| Evinrude 1057 | Fuel pump service tip for 4 thru 25 hp models | 9/74 |
| Evinrude 1069 | Throttle cam change for 1974 & 1975 hp models | 1/75 |
| Evinrude 1070 | O.M.C. Premium Blend gearcase lubricant | 2/75 |
| Evinrude 1082 | Non-recommended lubricants | 5/75 |
| Johnson 1388 |
New idle speed
control knob on 1974 & 75 - 9.9 & 15 |
8/75 |
| Johnson 1385 Rev.
1 |
Recommended fuel
for all to date - 2 thru V-6 |
9/75 |
| Evinrude 1092 | Fuel recommendations for 1976 200 hp V-6 | 9/75 |
| Evinrude 1101 | Outboard gasoline recommendations for all models | 9/75 |
| Johnson 1392 |
Permanently
installed fuel tanks on 1976 to date - V-6's |
10/75 |
| Evinrude 1103 | Permanently installed fuel tanks used with 1976 V-6 | 10/75 |
| Johnson 1399 |
Change in
carburetor orifice for 1976 - 55 & 75 |
12/75 |
| Evinrude 1108 | Change in carburetor orifice size for 1976 55 & 75 hp models | 1/76 |
| Evinrude 1109 | New OMC Hi-Vis gearcase lubricant | 1/76 |
| Johnson 1412 |
Change in choke
linkage on 1976 - V-4's |
4/76 |
| Johnson 1415 |
Throttle cam
adjustment tool on all models to date |
4/76 |
| Evinrude 1122 | Change in choke linkage on 1976 V-6 models | 4/76 |
| Johnson 1422 |
Hard starting in
cold weather on 1976 - V-6's |
6/76 |
| Evinrude 1134 | Hard starting in cold weather on 1976 200 hp model | 6/76 |
| Johnson 1427 |
Permanently
installed fuel systems on dual V-4, single or dual V-6 |
8/76 |
| Evinrude 1139 | Permanently installed fuel systems | 8/76 |
| Johnson 1429 |
Mid range
improvement on 1976 - 70 & 75 |
9/76 |
| Evinrude 1144 | 1976 70 & 75 hp mid-range improvement | 9/76 |
| Evinrude 1147 | Outboard gearcase capacities | 2/77 |
| Johnson 1438 |
HP restrictor kit
on 1969 thru 1978 - 25 reduced to 20 |
6/77 |
| Johnson 1441 |
Lower to upper
fuel pump hose on 1977 - V-6's |
7/77 |
| Evinrude 1154 | 20 hp restrictor kit | 7/77 |
| Evinrude 1158 | V-6 lower-to-upper fuel pump hose | 7/77 |
| Johnson 1453 |
Carburetor jet
sizes on all recent models |
1/78 |
| Evinrude 1168 | 1978 model E-4 hp (longshaft) | 1/78 |
| Evinrude 1172 | Carburetor jet sizes | 1/78 |
| Evinrude 1181 | 1978 Euro-4 long high speed orifice change | 3/78 |
| Johnson 1462 |
Carburetor
improvements on 1978 - V-6's |
4/78 |
| Evinrude 1186 | 1978 V-6 carburetor improvements | 4/78 |
| Johnson 1464 |
100:1 two cycle
lubricants not approved for any models to date |
5/78 |
| Johnson 1465 |
Lean won't idle -
Missing idle air bleeds on 1978 - 140 |
5/78 |
| Evinrude 1191 | Choke clevis wear and loosening due to vibration | 6/78 |
| Evinrude 1193 | 1978 140 hp idle air bleed restrictors | 6/78 |
| Johnson 1475 |
Loosening choke
clevis due to wear on 1978 - V-4's |
7/78 |
| Johnson 1479 |
Surging loss of
power - Orifice change on 1978 - 150 |
8/78 |
| Evinrude 1203 | 1978 150 hp high speed orifices | 9/78 |
| Johnson 1487 |
Loose choke
butterfly screws on 1972 thru 1978 - 50 |
12/78 |
| Evinrude 1211 | Loose choke butterfly screws | 1/79 |
| Johnson 1491 |
Lean idle -
Orifice change on 1979 - 175 |
2/79 |
| Johnson 1492 |
Engine not
turning up - air bleed change on 1979 - 150 |
2/79 |
| Evinrude 1217 | Carburetor improvements | 3/79 |
| Evinrude 1218 | Carburetor improvements | 3/79 |
| Evinrude 1219 | Evinrude outboard orifice plug chart (1967-1979) | 3/79 |
| Johnson 1493 |
Look alike float
chamber gaskets on 1978 to date, V-4's & V-6's |
4/79 |
| Evinrude 1220 | Correct float chamber gasket usage | 4/79 |
| Johnson 1501 |
Recommended
anti-siphon valves and fuel filter for all V-6's |
6/79 |
| Johnson 1503 |
Eliminating
insects from float bowl, add vent screen on 20 thru V-6 to date |
8/79 |
| Evinrude 1228 | Gearcase lubricant level all models | 8/79 |
| Evinrude 1232 | Evinrude - Carburetor bowl vent screen 20 thru V-6 models | 8/79 |
| Evinrude 1235 | Use of gasahol | 10/79 |
| Johnson 1509 Rev.
1 |
Use of gasahol
1978 to date on all models |
11/79 |
| Johnson 1514 |
Carburetor jet
change 1979 - 55 |
1/80 |
| Evinrude 1242 | Evinrude - Carburetor jet change - 1979 55 electric | 2/80 |
| Johnson 1515 |
Hand starting
cold engines on 1979 - 25 & 35 |
3/80 |
| Johnson 1516 Rev.
1 |
Carburetor Jet
Change |
3/80 |
| Johnson 1523 |
Revised fuel
octane recommendation on 1976 to date - V-6's |
3/80 |
| Johnson 1524 |
Fuel line vacuum
tester on V-4's & V-6's to date |
3/80 |
| Evinrude 1243 | Evinrude - Carburetor jet change - 1980 85 & 140 | 3/80 |
| Evinrude 1249 | Evinrude - Cold engine starting - 1979 25 & 35 | 3/80 |
| Johnson 1528 |
Eliminating
stalling after prolonged idle on 1980 - 50 and 1979 & 80 - 3 cyl. |
4/80 |
| Johnson 1529 |
Fuel economy
improvement on 1980 - 235 |
4/80 |
| Evinrude 1250 | Revise fuel recommendations | 4/80 |
| Johnson 1532 |
List of available
high, intermediate and low speed orifices - all fixed jet models |
5/80 |
| Evinrude 1253 | Evinrude - Use of gasahol | 5/80 |
| Evinrude 1259 | Adapter plate p/n 322313 - Loss of maximum RPM | 5/80 |
| Evinrude 1263 | Carburetor jet sizes | 5/80 |
| |
|
|
| ELECTRICAL AND
IGNITION SYSTEMS |
| Bulletin
# |
Subject |
Date |
| Johnson 1229 |
Testing clipper circuit on 1970 3 cyl. &
V-4's |
2/70 |
| Johnson 1237 |
New screw for anti-reverse contact &
insulator on 1969-70 3 cyl. & V-4's |
4/70 |
| Johnson 1239 |
Cleaning distributor caps on 1968 thru
1972-55 thru V-4 |
4/70 |
| Johnson 1248 | Incorrect use of spark plugs - Champion L-77V and UL-77V applications | 11/70 |
| Johnson 1249 |
Stator leads damaged by flywheel on 1970-50 |
12/70 |
| Johnson 1256 |
Short spark plug life due to charge coil or
connector leakage on 1971-50 |
3/71 |
| Johnson 1261 |
Purpose of reverse cut-off spring. Do not
remove from 55 thru V-4 |
5/71 |
| Johnson 1265 |
Causes of poor idle on 1971-50 |
7/71 |
| Johnson 1248 Rev. 1 | Revised surface-gap spark plug recommendations for 1971-72 models | 10/71 |
| Johnson 1277 |
New throttle cam prevents starting in gear
on 1972-40 |
10/71 |
| Johnson 1279 |
Servicing OMC CD system and new spark plug
boots |
1/72 |
| Johnson 1282 |
Erratic idle - Relieve back pressure -
Adjust carburetor on 1972 - 20 & 25 |
1/72 |
| Johnson 1284 |
Supplement to 1282 |
2/72 |
| Johnson 1286 | Pulse pack and rotor assembly 385036 installation and wiring on 1968 100 HP V-4 | 2/72 |
| Johnson 1287 |
Causes of damage to instrument cable on 1971
& 72 - 50, 65 & V-4 |
3/72 |
| Johnson 1288 | Tachometer installation not recommended on 1972 manual-start 50 HP | 3/72 |
| Johnson 1291 |
Intermittent firing due to poor ground
connection on 1967 thru 1972 - 100 & 125 |
3/72 |
| Johnson 1305 | Availability of alternate spark plugs for capacitor-discharge ignition models | 9/72 |
| Johnson 1308 | Wiring clamp 385535 prevents timer-base and sensor lead chafing on 1973 50 HP | 10/72 |
| Johnson 1310 |
New wiring clamp on timer base and sensor
for 1973 - 50 |
10/72 |
| Johnson 1312 Rev.
1 |
Proper use of jumper cables and battery
charging units - all models |
3/73 |
| Evinrude 1007 | Use of jumper cables and battery charging units on all outboards and Stern Drives with electric start | 4/73 |
| Johnson 1317 | Correcting spark advance lever interference on 85-135 HP V-4 motors | 5/73 |
| Johnson 1320 |
Electrical trouble shooting - Remote control
on 1973 - 50 thru 135 |
6/73 |
| Johnson 1322 |
Poor idle or hard starting characteristics
on 1973 - V-4 |
7/73 |
| Evinrude 1020 | Suppressor removal with Phase 11 Pulse pack models 100782-100783 and 100882- 100883 (Use 1076) | 8/73 |
| Johnson 1326 |
Ignition key blanks on 1973 to date - All
electric start models |
10/73 |
| Johnson 1327 |
Sensors grounding to sensor shield on 1973 -
50 thru 135 |
10/73 |
| Evinrude 1025 | Ignition key blanks for electric outboard and Stern Drive models | 11/73 |
| Evinrude 1028 | Protective sleeve to electrical leads for 1974 40 hp | 11/73 |
| Johnson 1335 |
Eliminate warm up choke on 1968 thru 1974 -
50 thru V-4's |
2/74 |
| Johnson 1336 |
Spark plug fouling on 1974 - 9.9 & 15 |
2/74 |
| Evinrude 1039 | Spark plug fouling on 1974 9.9 and 15 hp models | 2/74 |
| Johnson 1341 |
Ignition shut-off switches on 2 thru 135 to
date |
4/74 |
| Evinrude 1043 | Ignition shut off switches | 4/74 |
| Johnson 1345 |
Rerouting of ignition coil ground lead on
1974 - 2, 4 & 6 |
5/74 |
| Evinrude 1045 | Ignition coil service tip for 2, 4 and 6 hp models | 5/74 |
| Johnson 1359 |
Cam-point timing on 1974 & 1975 -
9.9, 15 & 40 |
10/74 |
| Johnson 1361 |
Electric trolling motor transistor failure
on 1974 to date |
10/74 |
| Evinrude 1063 | Cam - point timing for 9.9, 15 and 40 hp models | 11/74 |
| Johnson 1370 |
Stator service tip on 1973 thru 1975 - V-4's |
1/75 |
| Evinrude 1066 | Spark plug and ignition information for all 1970 through 1975 outboard models (Use 1124) | 1/75 |
| Johnson 1375 |
Pulse pack service tips on 1967 thru 1970 -
100 & 115 |
2/75 |
| Johnson 1380 |
Stator resistance reachings on 1974 to date
- 50 thru V-4 |
3/75 |
| Evinrude 1076 | Pulse pack service tips for 1967 - 1979 100 & 115 hp models | 3/75 |
| Evinrude 1077 | Stator service on 85 through 135 hp models with magneto C.D. ignition | 3/75 |
| Johnson 1382 |
Water in power packs on 1973 thru 1975 - 50
thru 135 |
5/75 |
| Evinrude 1083 | Stator resistance readings 1974 - 1975 50 through 135 hp models | 5/75 |
| Evinrude 1085 | Battery cable extensions and splicing procedure for electric trolling outboard 9.9 through 135 models | 6/75 |
| Evinrude 1089 | Water in power packs of 1973 through 1975 50 through 135 hp models | 6/75 |
| Evinrude 1091 | Amplifiers and pulse packs for 1971 - 1972 models | 7/75 |
| Johnson 1383 |
New driver coil for 1974 thru 1976 -
9.9, 15 & 40 |
8/75 |
| Evinrude 1097 | Alternate spark plug for 1974-75 9.9, 15 & 40 hp models | 8/75 |
| Evinrude 1095 | (Revised) New driver coil assembly p/n 581557 1974-75 9.9, 15 and 40 hp with electric start | 9/75 |
| Johnson 1381 |
Rev. 1 Battery cable extension &
splicing on all electic models to date |
10/75 |
| Evinrude 1104 | Battery cable extensions and splicing procedure for electric trolling outboard 9.9 through 200 hp models | 10/75 |
| Johnson 1400 |
Incorrect power pack usage on 1972 thru 1976
- 3 cyl. & V-4's |
12/75 |
| Evinrude 1107 | Incorrect usage of power packs for 70 - 135 hp models | 12/75 |
| Johnson 1402 |
Correction to Service Manual on 1976 - 200 |
1/76 |
| Johnson 1409 |
Rev. 1 Change in wiring location on 1969
thru 76 - 4 |
2/76 |
| Evinrude 1120 | Change in high tension lead location for all 1969 thru 1976 4 hp | 3/76 |
| Evinrude 1124 | Evinrude spark plug information for all 1952 thru 1976 outboard models | 4/76 |
| Evinrude 1126 | Spark plug wet fouling on 25 hp models | 4/76 |
| Johnson 1418 |
Electric trolling motor - Battery
installation procedure on all models to date |
5/76 |
| Evinrude 1129 | Hard starting or erratic ignition on 1969 & 1970 115 hp | 5/76 |
| Johnson 1425 |
Armature plate
bearing improvements and lubrication on 1974 thru 1976 - 9.9, 15, 35 & 40 |
6/76 |
| Evinrude 1130 | Recommended battery hook-up with outboard and electric outboard | 6/76 |
| Evinrude 1136 | Armature plate bearing assembly and lubrication for 9.9/15 hp 1974-1976; 35 hp 1976; 40 hp 1974 - 1976 | 7/76 |
| Johnson 1428 |
Electrical components bracket and ground
leads on 1976 - V-6's |
8/76 |
| Evinrude 1140 | V-6 outboard electrical components brkt. ground lead | 9/76 |
| Johnson 1433 |
Termination of rework program on Delco
stator on 1961 thru 1966 - V-4's |
12/76 |
| Evinrude 1146 | Termination of rework program on #378337 stator | 1/77 |
| Evinrude 1148 | Trouble shooting battery CD ignition | 2/77 |
| Johnson 1435 |
Heavier battery cables used on 1977 - V-6's |
5/77 |
| Johnson 1414 |
Rev. 1 Hard starting or erratic ignition on
1969 & 1970 - 115 |
6/77 |
| Johnson 1439 |
Accessory ignition shut-off device on 1973
to date - 50 thru V-6 |
6/77 |
| Johnson 1442 |
Thermostat kit on 1974 thru 1976 - 40 |
7/77 |
| Johnson 1443 |
Sensor resistance and leakage tests on 1977
- 50 |
7/77 |
| Evinrude 1156 | 1977 50 hp sensor resistance and leakage tests | 7/77 |
| Johnson 1445 |
Armature plate improvement kit on 1973-1976
- 20 & 25 |
8/77 |
| Evinrude 1161 | Armature plate improvement kit | 9/77 |
| Evinrude 1163 | Trouble shooting battery C.D. ignition | 9/77 |
| Johnson 1447 |
Change in flywheels on 1978 - V-4's |
10/77 |
| Evinrude 1165 | Power pack usage, 1968 thru 1978 4 hp - 235 hp | 12/77 |
| Evinrude 1166 | 1978 V-4 flywheels | 12/77 |
| Evinrude 1173 | Spark plug information all 1952 thru 1978 outboard models | 2/78 |
| Johnson 1454 |
Ignition coil internal changes on 1968 thru
1973 - 50 thru V-4's |
3/78 |
| Johnson 1456 |
Assuring good electrical connections on 1977
power pack models to date |
3/78 |
| Evinrude 1179 | Ignition coil internal changes | 3/78 |
| Evinrude 1180 | Good electrical connections | 3/78 |
| Johnson 1471 |
Voltage regulator kit on 6, 9 or 10 amp alternators to date |
7/78 |
| Johnson 1482 |
New hot horn on 1973 thru 1978 - 50 thru V-6 |
10/78 |
| Johnson 1483 |
Wire shorting in remote control on 1979 - 55
thru V-6 |
10/78 |
| Johnson 1488 |
Armature plate and pilot replacement kit on
1974 thru 1976 - 9.9, 15 & 35 |
1/79 |
| Evinrude 1212 | Armature plate and pilot replacement kit p/n 389813 | 1/79 |
| Johnson 1419 |
Rev. 2 Spark plug chart on all models to
date |
2/79 |
| Evinrude 1215 | Spark plug information for all 1952-1979 outboard models | 2/79 |
| Evinrude 1216 | Power pack usage - 1968 thru 1979 4 hp - 235 hp | 2/79 |
| Johnson 1494 |
Neutral start switch mounting nuts loosening
on 1978 to date - 25 & 35 |
4/79 |
| Johnson 1501 |
Cause of safety switches burning out on 1974
to date - 25, 35 & 40 |
6/79 |
| Johnson 1448 |
Rev. 1 Power pack usage on 1968 thru 1979 -
4 thru V-6's |
7/79 |
| Johnson 1504 |
Timer base lead interference on 1979 - V-4's |
8/79 |
| Evinrude 1230 | Timer base leads interference - 1979 V-4 models | 9/79 |
| Johnson 1508 |
Parts Catalog error on 1978 - 55 |
11/79 |
| Johnson 1520 |
Minimum battery capacity recommendations on
electric troll thru V-6 to date |
3/80 |
| Johnson 1527 |
Identifying Delta Amplifier leads on 1970
& 71 - 60, 1970 thru 72 - 85 &
100 |
4/80 |
| Johnson 1531 |
High reading temperature gauge and ammeter
battery overcharge on 1978 thru 1980 - V-4's & V-6's |
4/80 |
| Evinrude 1245 | Marine batteries | 4/80 |
| Johnson 1533 |
Missing or failure to reach full RPM -
incorrect rotor 1969 & 70- 115 |
5/80 |
| Evinrude 1255 | Evinrude - Delta amplifiers | 5/80 |
| Evinrude 1256 | Evinrude - Voltage regulators 1978 thru 1980 V-4 & V-6 | 5/80 |
| Evinrude 1262 | P/N 385038 pulse pack kit 1969-70 115 | 5/80 |
| |
|
|
| POWERHEAD,
MANUAL STARTER AND MOTOR COVER |
| Bulletin
# |
Subject |
Date |
| Johnson 1244 |
Length of manual
starter rope required for various models |
9/70 |
| Johnson 1266 |
Correct
installation of flywheel key on 1971 - 3 thru 25 |
7/71 |
| Johnson 1267 |
Overheating from
separation of impeller & hub; supplement to 1103 |
7/71 |
| Johnson 1270 |
New spacer
prevents distortion of control panel on 1971 - 2 |
9/71 |
| Johnson 1273 |
Change in
flywheel nut torque on 1972 - 50 thru V-4 |
9/71 |
| Johnson 1275 |
Oversize pistons
and rings for KC-13R Stinger racing model |
10/71 |
| Johnson 1276 |
Cause of starter
spring breakage on 6 and 9.5 |
10/71 |
| Johnson 1280 |
Change in starter
lockout cam adjustment on 1972 - 50 |
2/72 |
| Johnson 1289 | Replacement Stinger 2 65 HP motor cover assembly and detail parts | 3/72 |
| Johnson 1294 |
Lubricating spark
advance lever at safety switch contact on 1972 - 50 |
6/72 |
| Johnson 1313 |
Defective
cylinder to crankcase bolts on 1973 - 85 thru 135 |
1/73 |
| Evinrude 1002 | Defective cylinder to crankcase bolts 1973 85 - 125 hp | 1/73 |
| Evinrude 1003 | 1.5 - 2 hp powerhead disassembly | 2/73 |
| Evinrude 1010 | New procedure for adjusting starter lockout lever on 1973 18-25 hp models | 4/73 |
| Johnson 1321 |
New procedure for
adjusting starter lockout lever on 1973 - 20 & 25 |
6/73 |
| Evinrude 1015 | Assuring full throttle advance 1973 85 thru 135 hp models | 7/73 |
| Evinrude 1022 | Engine starting speed on all 1974 50 - 135 hp models | 9/73 |
| Johnson 1333 |
Water in lower
cylinder on 1971 thru 1974 - 50 |
1/74 |
| Evinrude 1031 | Moving cable clamp on 1973 - 1974 50 hp models | 1/74 |
| Evinrude 1034 | Water in lower cylinder 1971 - 1974 50 hp models | 1/74 |
| Evinrude 1037 | Cylinder head screws - Silver Starflite | 2/74 |
| Johnson 1340 |
Jumping out of
gear and starter repair on 1974 - 9.9 & 15 |
3/74 |
| Johnson 1344 |
Lockout lever
removal on 1973 & 1974 - 20, 25 & 40 |
5/74 |
| Johnson 1347 |
Water in cylinder
on 1971 thru 1974 - 50 |
5/74 |
| Evinrude 1047 | Piston failures on 1973 - 1974 135 hp models | 5/74 |
| Evinrude 1048 | Water in cylinders of 1971 - 1974 50 hp models | 5/74 |
| Evinrude 1054 | Hard starting 1972 - 1973 50 hp rope start models | 8/74 |
| Johnson 1352 |
Water in cylinder
on 1973 & 1974 - 135 |
9/74 |
| Johnson 1357 |
Flywheel key
installation on 1974 & 1975 - 9.9 & 15 |
9/74 |
| Evinrude 1056 | Horsepower restriction kit p/n 387219 for 1974 - 1975 9.9 hp | 9/74 |
| Johnson 1358 |
Correct number of
starter spool turns on 1974 - 6 |
10/74 |
| Evinrude 1059 | Flywheel key installation on 1974 - 1975 9.9 & 15 hp models | 10/74 |
| Evinrude 1062 | Horsepower restriction kit p/n 387028 for 1969-75 25 hp | 11/74 |
| Evinrude 1058 | Water in cylinders of 1973 - 1974 135 hp models | 12/74 |
| Evinrude 1065 | High performance cylinder head kit p/n 386998 1975 75 hp models | 12/74 |
| Johnson 1365 |
High performance
head kit on 1975 thru 1978 - 75 |
1/75 |
| Johnson 1376 |
Low compression
cylinder heads on 1970 thru 1975 - 3 cyl. |
2/75 |
| Evinrude 1072 | Low compression cylinder head kits for 1970-1975 60, 65 & 70 hp models | 2/75 |
| Johnson 1391 |
Product
improvements on 1976 - 70 & 75 |
9/75 |
| Evinrude 1106 | 1976 70 & 75 hp product improvements | 11/75 |
| Johnson 1406 |
Change in
cylinder head torque on 1976 - 35 |
1/76 |
| Johnson 1405 |
Engine overheating on 1976 - 35 |
2/76 |
| Evinrude 1114 | Cylinder head torque and proper break-in for 1976 55 hp models | 2/76 |
| Johnson 1413 |
New cylinder head
gasket coating on 1976 - 9.9 thru V-6 |
4/76 |
| Evinrude 1125 | New cylinder head gasket coating for 9.9 thru 200 hp models | 4/76 |
| Johnson 1420 |
Retorquing of
cylinder head bolts on 2 thru V-6 to date |
6/76 |
| Johnson 1424 |
Service Manual
correction on 1976 - V-6's |
6/76 |
| Evinrude 1131 | Retorquing of cylinder head bolts on all 2 thru 200 hp models | 6/76 |
| Johnson 1421 |
Changes in 1977
models - 2 thru V-6 |
7/76 |
| Johnson 1431 |
Crankshaft
appearance on 1970 thru 1973 - 40 |
9/76 |
| Evinrude 1142 | 40 hp crankshaft appearance | 9/76 |
| Johnson 1436 |
Cause of
overheating on 1976 thru 1978 - 35 |
5/77 |
| Evinrude 1157 | Thermostat kit #388700 (1974-76 40 hp) | 7/77 |
| Johnson 1449 |
Improvements to
manual start engines 1977 - 50 |
1/78 |
| Johnson 1451 |
Piston rings on
9.9 & 15 to date |
1/78 |
| Evinrude 1170 | 1977 50 hp manual start engines | 1/78 |
| Evinrude 1175 | 9.9 and 15 hp piston rings, p/n 386279 and 386280 | 1/78 |
| Evinrude 1176 | Cylinder roboring and repair | 2/78 |
| Johnson 1480 |
Special
crankshaft seal rings on 1978 to date - V-4's & V-6's |
8/78 |
| Evinrude 1204 | — Special crankshaft seal rings | 9/78 |
| Johnson 1473 Rev.
1 |
Cylinder piston
to skirt clearance on 1977 & 1978 - 2 thru 235 |
10/78 |
| Evinrude 1199 | Cylinder to piston skirt clearance (1977 thru 1979) revised | 10/78 |
| Johnson 1484 |
Starter pawl
return spring on 1979 - 9.9 & 15 |
11/78 |
| Evinrude 1208 | Starter pawl return spring p/n 325913 | 11/78 |
| Johnson 1485 |
Repairing broken
starter mounting boss on 1976 to date - V-6's |
12/78 |
| Evinrude 1209 | V-6 starter mounting boss - all V-6's | 12/78 |
| Evinrude 1221 | 25-35 neutral start switch mounting nuts | 4/79 |
| Johnson 1499 |
Lower motor cover
rattling on 1979 - V-4's |
6/79 |
| Evinrude 1226 | Lower motor cover rattle on V-4 models | 7/79 |
| Evinrude 1233 | Overheating due to blockages of cylinder water passages | 8/79 |
| Johnson 1502 Rev.
1 |
Low compression
heads for commercial use on 1977 to date - 3 cyl. V-4's & V-6's |
10/79 |
| Johnson 1507 |
Overheating due
to blockages of cylinder water passages on 1979 - 4 |
11/79 |
| Johnson 1519 |
Proper use of OMC
Gel Seal on all models to date |
3/80 |
| Evinrude 1244 | Evinrude - OMC Gel Seal, cylinder block to crankcase sealing | 3/80 |
| Johnson 1534 |
Proper method of
selecting correct oversize bore - 1969 thru 1979 - all models |
5/80 |
| Evinrude 1264 | Evinrude - Bore sizes, standard engines | 5/80 |
| |
|
|
MID SECTION AND
LOWER UNIT |
| Bulletin
# |
Subject |
Date |
| Johnson 1238 |
Installing converging ring on 1968 to date
all thru-hub exhaust |
4/70 |
| Johnson 1243 |
Eliminating overheating of propeller hub on
1969 & 70 - V-4's |
8/70 |
| Johnson 1246 |
Heavy duty mounts for 1970 thru 1972 - 60 |
10/70 |
| Johnson 1252 |
Overheating propeller hubs; supplement to
1243 |
1/71 |
| Johnson 1253 |
Order correct swivel bracket seals on 1968
thru 1971 - 55 & 60 |
1/71 |
| Johnson 1257 |
Causes of driveshaft breakage on 1971 - 40 |
3/71 |
| Johnson 1258 |
Installing gearcase solenoid shift rods on
1971 - 50 thru V-4 |
4/71 |
| Johnson 1274 |
New oil pump - service procedure on 1968
thru 1971 3 cyl. |
10/71 |
| Johnson 1278 |
Advantages of using SST propellers from 1971
to date |
12/71 |
| Johnson 1281 |
"Snap" shift improvement on 1960
thru 1970 - 18, 20 & 25 |
1/72 |
| Johnson 1282 |
Erratic idle - relieve back pressure -
adjust carburetor on 1972 - 20 & 25 |
1/72 |
| Johnson 1284 |
Supplement to 1282 |
2/72 |
| Johnson 1285 | Replacement converging rings for aluminum and SST through-hub propellers | 2/72 |
| Johnson 1290 |
Securing propeller nut on 9.5, 20 & 25 |
3/72 |
| Johnson 1297 |
Servicing 1968-69 hydro electric gearcases -
Correct parts needed |
6/72 |
| Johnson 1299 | Revised gearcase-to-exhaust-housing attaching screw for 1964-72 9½ HP | 7/72 |
| Johnson 1300 |
Proper use of flushettes on any adaptable
model to date |
7/72 |
| Johnson 1303 |
Replacing stern bracket clamps on 1972 - 50
thru V-4 |
8/72 |
| Johnson 1309 |
New drain plug and magnet on 1973 - 50 thru
135 |
10/72 |
| Johnson 1307 |
Tank testing - Holding shift in gear during
test on 1973 - 50 thru V-4 |
1/73 |
| Johnson 1314 |
New procedure for installing propellers on
all thru-hub exhaust |
4/73 |
| Johnson 1315 |
New neutral detent feature added to 1973 -
50 thru 135 |
4/73 |
| Evinrude 1008 | New procedure for installing propellers on all with thru-hub exhaust models | 4/73 |
| Johnson 1316 | Low gearcase oil level warning for specified 1973 65 HP motors | 5/73 |
| Evinrude 1012 | Very low gearcase oil level on all 1973 50 and 65 hp models | 5/73 |
| Evinrude 1017 | New neutral detent feature added on 1973 50 thru 135 hp models | 7/73 |
| Johnson 1325 |
New trailering lock arm on 1973 - 65 long
& V-4's |
9/73 |
| Evinrude 1023 | Test program for all 1973 50 - 135 hp models manufactured prior to 1-1-73 | 9/73 |
| Johnson 1337 |
Plunger and snap ring program on 1973 - 50
thru 135 |
2/74 |
| Johnson 1339 |
Checking thrust rod on all models to date |
3/74 |
| Johnson 1340 |
Jumping out of gear and starter repair on
1974 - 9.9 & 15 |
3/74 |
| Evinrude 1042 | Checking the angle adjusting rod on all outboard models | 4/74 |
| Johnson 1343 |
Selecting correct mounting bolts on 1973 to
date - 55 thru V-6 |
5/74 |
| Johnson 1346 |
Lubrication of tilt tube on 1973 & 1974
- 35 thru V-6 |
5/74 |
| Johnson 1349 |
E-Z-Duzit Gearcase lubrication fitting on
all outboards and Stern Drives to date |
7/74 |
| Johnson 1350 |
Service tips - tilt assist shocks on 1975 -
70 thru 135 |
7/74 |
| Evinrude 1052 | E-Z Duzit gearcase lubrication fitting for all outboards & Stern Drives | 7/74 |
| Johnson 1356 |
Using correct propeller bushing on 1975 - 50
thru 135 |
9/74 |
| Evinrude 1060 | Using correct propeller thrust bushing on 1975 50 - 135 hp models | 10/74 |
| Johnson 1369 |
Gear shift adjustment on 1975 - 9.9 & 15 |
1/75 |
| Johnson 1372 |
Leakage at oil fill/drain hole on 1975 - 4W |
2/75 |
| Johnson 1374 |
Selecting correct gearcase on 1975 - 70 B
& E models |
2/75 |
| Evinrude 1071 | Water pump impeller p/n 385528 for 1973-1975 85 - 135 hp models | 2/75 |
| Evinrude 1073 | New style impeller housings for 50 - 135 hp models | 3/75 |
| Evinrude 1075 | Leakage at oil drain/fill hole on model 4506 | 3/75 |
| Evinrude 1078 | Impeller housing p/n 310000 used on: 1964-1973 9½ hp models | 3/75 |
| Evinrude 1079 | Selecting correct gearcase for 1975 70 hp models 70572B, 70572E, 70573B, 70573E | 3/75 |
| Johnson 1363 |
Trim and tilt service tips on 1975 thru 1977
- 50 thru 140 |
4/75 |
| Johnson 1379 |
Small gearcase clutch dog on 1975 - 50 &
75 |
4/75 |
| Johnson 1377 |
New impeller housings on 1975 all models to
date |
5/75 |
| Johnson 1378 Rev.
1 |
Gearcase field modification program on 1975
- 70 thru 135 |
5/75 |
| Evinrude 1084 | Correct installation of 319895 clutch dog shifter for 1975 50 hp and short 75 hp small gearcase models | 5/75 |
| Evinrude 1080 | Gearcase field modification Rev. 1 program | 6/75 |
| Evinrude 1081 | Propeller recall - for 9½ hp plastic props | 6/75 |
| Evinrude 1087 | Gearcase field modification identification for 1975 70, 85, 115 and 135 hp models | 6/75 |
| Evinrude 1090 | Clutch dog pin springs p/n 313454 or 320311 for 50 - 135 hp models | 6/75 |
| Johnson 1384 |
Incorrect model/serial number plates on 1975
- 70 |
7/75 |
| Johnson 1387 |
Exhaust emulsion draining from gearcase on
1974 & 1975 - 9.9 & 15 |
8/75 |
| Johnson 1389 |
Improving reverse thrust on displacement
hulls for 1974 thru 1976 - 9.9 & 15 |
8/75 |
| Evinrude 1096 | Water pump impeller p/n 385528 for 1973-75 85 through 135 hp models | 8/75 |
| Evinrude 1099 | Oil - water emulsion draining from gearcase of 1974 - 1975 9.9 & 15 hp models | 9/75 |
| Evinrude 1100 | Improving reverse thrust on displacement hulls for 9.9 & 15 hp 1974 thru 1976 models | 9/75 |
| Johnson 1393 |
Trim and tilt cylinder assemblies on 1973
thru 1976 - 50 thru 135 |
10/75 |
| Johnson 1394 |
New gearcase lubricant on all 1 1/2 thru V-6
to date |
12/75 |
| Johnson 1396 |
Replacement water pump liner on 1976 - 4 90°
drive |
12/75 |
| Johnson 1397 |
Cooling system modification program on 1976
- 35 |
12/75 |
| Johnson 1398 |
Proper mounting of engine on 1976 to date
V-6's |
1/76 |
| Johnson 1407 |
New plastic water
pump housing on 1974 thru 1976 - 9.9 & 15 |
2/76 |
| Johnson 1410 |
Operation of
manual release valve on 1976 - V-6’s |
2/76 |
| Evinrude 1110 | Cooling system modification program for 1976 35 hp models | 2/76 |
| Evinrude 1111 | Replaceable liner water pump for 1976 4 hp model | 2/76 |
| Evinrude 1117 | Engine overheating on 1976 35 hp model | 3/76 |
| Johnson 1417 |
Replacement of
gearcases on 1976 - 35 |
4/76 |
| Evinrude 1121 | New plastic bodied water pump housing for 1974-76 9.9 & 15 hp models | 4/76 |
| Evinrude 1127 | Replacement of gearcases for 1976 35 hp | 5/76 |
| Evinrude 1137 | Plastic converging ring installation on aluminum thru-hub props 50 hp thru V-4 outboards | 7/76 |
| Johnson 1430 |
Oil pump service
assemblies on 1976 — V-4’s |
9/76 |
| Johnson 1432 |
Lower mounts on
V-4’s & V-6’s to date |
9/76 |
| Evinrude 1141 | Oil pump service assembly #385056 | 9/76 |
| Evinrude 1145 | 140 hp motors on Bass Boats | 1/77 |
| Evinrude 1150 | Freeze damage to water pumps and gearcases | 5/77 |
| Evinrude 1152 | 35 hp motor overheating | 5/77 |
| Johnson 1440 |
Plastic water
pump impeller housing failures on all models to date |
7/77 |
| Johnson 1444 |
Correction to
1977 Master Parts Price Book |
7/77 |
| Evinrude 1160 | Plastic water pump impeller housing failures | 7/77 |
| Johnson 1446 |
Troubleshooting
integral T—N—T on 1977 to date 75, V-4’s & V-6's |
10/77 |
| Johnson 1450 |
Service gearcase
on 1977 & 1978 - V-6’s |
1/78 |
| Johnson 1452 |
Obsolete water
pump repair kits on various years and models |
1/78 |
| Evinrude 1171 | V-6 service gearcase | 1/78 |
| Evinrude 1174 | Obsolete water pump repair kits | 1/78 |
| Johnson 1455 |
Pinion gear nut
torque specification on 1976-1978 - V-6’s |
3/78 |
| Evinrude 1182 | V-6 pinion & bearing gear nut specification | 3/78 |
| Johnson 1459 |
Power trim valve
noise on V-6's |
4/78 |
| Johnson 1460 |
Removal of
driveshaft from 1976 to date V-4’s & V-6’s |
4/78 |
| Johnson 1461 |
Lifting engines
by exhaust housing covers on 1978 to date V-4’s & V-6’s |
4/78 |
| Evinrude 1183 | Removal of driveshaft in V-4 and V-6 gearcase | 4/78 |
| Johnson 1466 |
Servicing
integral T-N-T on 1978 to date |
7/78 |
| Johnson 1467 |
T-N-T stuck in
tilted position on 1978 - V-4’s & V—6's |
7/78 |
| Johnson 1468 |
Adjusting
indicator gauge on integral T-N-T |
7/78 |
| Johnson 1470 |
Change in lower
mount system on 1977 - 25 to date, 1978 - 35 to date |
7/78 |
| Johnson 1463 Rev.
1 |
Water pump
improvements on 1978 - 35 |
8/78 |
| Johnson 1477 |
Separation of
integral T-N-T valves from 1976 to date |
8/78 |
| Johnson 1478 |
Corrosion of
check valve on 1973 thru 1977 Prestolite T-N-T |
8/78 |
| Johnson 1481 |
Lock up of tilt
and reverse lock on 1977 — 140 & 1978 - 3 cyl. & V-4’s |
8/78 |
| Evinrude 1187 | 1978 35 hp water pumps (revised) | 9/78 |
| Johnson 1497 |
Procedure for
shimming pinion gear on 1979 - 55 |
6/79 |
| Johnson 1498 |
Replacement of
relief valve o'ring on integral T-N-T |
6/79 |
| Evinrude 1225 | Shimming pinion gear | 7/79 |
| Johnson 1505 |
Causes of
propeller shaft breakage on 1977 & 1978 — 25 |
8/79 |
| Johnson 1506 |
Gearcase
lubricant level on all models to date |
8/79 |
| Evinrude 1229 | Evinrude - 25 hp propeller and driveshaft breakage | 8/79 |
| Johnson 1510 |
Extension kit
omission in Parts Catalog on 1980 — 4.5 & 7.5 |
12/79 |
| Johnson 1513 |
Eliminating shift
shaft sticking on 1976 thru 1979 - 25 & 35 |
1/80 |
| Johnson 1514 |
Driveshaft to
crankshaft spline wear on 2 & 4 to date |
3/80 |
| Johnson 1517 |
Power loss due to
hole burned in megaphone on 1979 - 150 thru 200 |
3/80 |
| Johnson 1518 |
Premature pinion
bearing failure on 1976 to date V-6’s |
3/80 |
| Johnson 1525 |
Correct
installation of clutch dog on 1980 - 4.5 & 7.5 |
3/80 |
| Evinrude 1247 | Driveshaft to crankshaft spline wear | 3/80 |
| Johnson 1530 |
Steering handle
kits for 1979 - 6,1974 thru 1980 - 9.9 & 15,1979 thru 80 - 25/35 and 55
rope |
4/80 |
| Evinrude 1254 | — Shifter clutch dog p/n 326340 1980 4.5 & 7.5 | 4/80 |
| Johnson 1535 |
Improved bearing
and gear kits/special alignment tool - 1960 thru 1979 - 18, 20 & 25 |
5/80 |
| Evinrude 1258 | Evinrude - Premature pinion bearing failure V-6 | 5/80 |
| Evinrude 1261 | Evinrude - Improved bearing & gear kits 1969 thru 1980 18, 20 & 25 | 5/80 |
| |
|
|
| CONTROLS AND
RIGGING |
| Bulletin
# |
Subject |
Date |
| Johnson 1241 |
Remote steering system installation on 1970
- 33 thru 115 |
8/70 |
| Johnson 1296 |
Proper mounting of engine on 1972 to date -
50 thru V-6 |
6/72 |
| Johnson 1302 |
New steering installation recommendations on
1973 thru 77 - 50 thru V-4 |
8/72 |
| Johnson 1308 | Ignition key numbers and replacement key identification for 1973 remote controls | 10/72 |
| Johnson 1306 |
Proper shift and throttle cable adjustment
1973 - 50 thru V-4 |
1/73 |
| Evinrude 1005 | 1973 remote control and harness for 50, 65, 85, 115 & 135 hp motors | 3/73 |
| Johnson 1318 |
Remote controls without "start in
neutral only feature" on 1973 to date - 50 thru V-6 |
5/73 |
| Johnson 1319 |
Potentially dangerous steering kits on 1973
to date - 50 thru V-6 |
6/73 |
| Johnson 1320 |
Electrical trouble shooting of remote
control on 1973 - 50 thru 135 |
6/73 |
| Evinrude 1014 | Electrical trouble shooting all magneto CD ignition models 50 - 135 hp | 6/73 |
| Evinrude 1016 | Remote control installations for 1973 50 - 135 hp outboards | 7/73 |
| Evinrude 1021 | Stern bracket to boat transom hardware on 1974 70 hp long shaft and V-4 models | 9/73 |
| Evinrude 1024 | 1974 trailering lock arm for 1973 65 hp (long) and V-4 models | 11/73 |
| Evinrude 1030 | —_ Gear shift assembly p/n 377943 for 1974 6 & 25 hp motors | 11/73 |
| Evinrude 1036 | Defective pivot screw p/n 122680 on model 135489 | 1/74 |
| Evinrude 1046 | Lockout lever p/n 317657 for 1973-1974 18, 25 and 40 hp | 5/74 |
| Evinrude 1049 | Lubrication of tilt tube of all 1973-1974 50 - 135 hp models | 5/74 |
| Evinrude 1050 | — Selecting the correct engine mounting bolts for all models with adjustable transom brackets | 6/74 |
| Evinrude 1053 | Service tips-tilt-assist shock absorbers for models 70573, 75543, 85593, 115593, 135543 and 135583 | 8/74 |
| Johnson 1360 |
Correct method of attaching remote cables on
1975 - 70 & 75 |
10/74 |
| Evinrude 1061 | Installing remote control cables to 1975 70 & 75 hp models | 11/74 |
| Evinrude 1067 | Dual engine steering system recommendation for 1973-1975 50 thru 135 hp models | 1/75 |
| Evinrude 1068 | Gear shift adjustment 1975 9.9 and 15 hp models | 1/75 |
| Evinrude 1098 | New idle speed control knob for 1974 7.5, 9.9 & 15 hp models | 8/75 |
| Evinrude 1102 | Lifting or removing 1976 V-6 engine from shipping carton | 9/75 |
| Johnson 1404 |
Steering and fuel systems and drywell drain
holes on 1976 to date - V-6's |
2/76 |
| Evinrude 1112 | Proper mounting of 1976 200 hp outboard | 2/76 |
| Johnson 1408 |
Possible interference in steering system on
1976 to date - 35 |
3/76 |
| Evinrude 1118 | Operation of manual release valve on 1976 200 hp | 3/76 |
| Evinrude 1119 | Possible interference in steering system on 1976 35 hp with thru-the-pivot steering | 3/76 |
| Evinrude 1143 | Lower mounts for 175 and 200 hp all, 140 hp all, 85 and 115 hp, 25 inch transoms | 9/76 |
| Evinrude 1149 | V-6 instrument cable (revised) | 5/77 |
| Johnson 1457 |
Field replacement program for OMC acessory
controls |
4/78 |
| Johnson 1458 |
Substituting motor tilt tube "Teleflex
Bulletin" |
4/78 |
| Evinrude 1185 | Motor pivot tube | 4/78 |
| Evinrude 1192 | 25 & 35 hp lower mount system | 6/78 |
| Johnson 1476 |
Remote control, dual installation with T-N-T
on 1978 - V-4's & V-6's |
7/78 |
| Evinrude 1205 | Tilt and reverse lock lever lock up | 9/78 |
| Evinrude 1206 | Newhot horn | 10/78 |
| Evinrude 1207 | Remote control wire shorting | 10/78 |
| Evinrude 1213 | All outboards with tilt tube steering | 2/79 |
| Evinrude 1241 | Evinrude - Shift shaft sticking 1976 thru 1979 25 & 1977 thru 1979 35 | 1/80 |
| Johnson 1521 |
Correct installation of OMC long lifeTM
(type "0") remote control cables |
3/80 |
| Johnson 1537 |
Safety related considerations in rigging and
testing a boat and motor |
5/80 |
| Evinrude 1257 | Evinrude - Safety related considerations in rigging | 5/80 |
| |
|
|
| TOOLS AND
ACCESSORIES |
| Bulletin
# |
Subject |
Date |
| Johnson 1242 |
Adjusting low speed needles on 1970 - 3 cyl.
& V-4's |
8/70 |
| Johnson 1319 |
Potentially dangerous steering kits on 1973
to date - 50 thru V-6 |
6/73 |
| Evinrude 1018 | Installing power tilt kit # 172509 on 1973 65 hp (long) and V-4 models | 7/73 |
| Johnson 1366 |
Dual steering recommendation on 1973 to date
- 50 thru V-6 |
1/75 |
| Johnson 1363 |
Trim and tilt service tips on 1975 thru 1977
- 50 thru 140 |
4/75 |
| Evinrude 1086 | Power trim and tilt service tips for 50 through 135 hp models | 6/75 |
| Evinrude 1088 | Tempo Tiltamatic | 6/75 |
| Johnson 1393 |
Trim and tilt cylinder assemblies for 1973
thru 1976 - 50 thru 135 |
10/75 |
| Evinrude 1105 | Availability of complete trim/tilt cylinders | 10/75 |
| Johnson 1401 |
12 amp alternator kits for 1976 to date -
55, 70 & 75 |
1/76 |
| Johnson 1403 Rev.
1 |
Ammeter kits for 1976 to date - V-6's |
1/76 |
| Evinrude 1113 | 12 AMP alternator kits p/n 172651 and 173276 installed on 1976 55, 70 and 75 hp models | 2/76 |
| Evinrude 1115 | Ammeter kits p/n 172994 & 172995 used with 1976 200 & 235 hp sport models | Date not shown |
| Evinrude 1128 | Dole power trim and tilt kit J-7376 | 5/76 |
| Johnson 1423 |
Causes of tachometer failures to date |
6/76 |
| Evinrude 1135 | Tachometer failures p/n 172254, 172709, 172930, 172258, 172710, 172931, 172674, 172928, 172675, 172929, 173226, 173049 | 6/76 |
| Johnson 1426 |
I nstalling plastic converging rings on 50
thru V-4's to date |
7/76 |
| Johnson 1437 |
Test prop RPM with reverse thrust kit on
1976 to date - 9.9 & 15 |
6/77 |
| Johnson 1439 |
Accessory ignition snut off device for 1973
to date - 50 thru V-6 |
6/77 |
| Evinrude 1159 | Part number 172866 accessory ignition shut off device | 7/77 |
| Johnson 1416 Rev.
1 |
"Dole" power trim & tilt kit |
8/77 |
| Evinrude 1162 | Dole power trim and tilt kit, model S# 7377 | 9/77 |
| Evinrude 1164 | K & O dynamometer | 9/77 |
| Johnson 1446 |
Troubleshooting integral T-N-T on 1977 on
date - 75, V-4's & V-6's |
10/77 |
| Evinrude 1167 | Troubleshooting the V-4 & V-6 tilt and trim units | 12/77 |
| Evinrude 1169 | Permatex Gel-Gasket | 1/78 |
| Evinrude 1177 | Hydraulic tilt & trim pump check valve repair kit 173569 | 2/78 |
| Evinrude 1178 | Power trim valve noise | 3/78 |
| Evinrude 1184 | Lifting 1978 V-4 & V-6 outboards | 4/78 |
| Evinrude 1189 | Integral power trim and tilt servicing | 5/78 |
| Johnson 1469 |
Vertical elevating devices on models to date |
7/78 |
| Johnson 1471 |
Voltage regulator kit 6, 9 or 10 amp
alternators on models to date |
7/78 |
| Johnson 1472 |
Emergency engine cooling using "Trouble
Cooler" on models to date |
7/78 |
| Evinrude 1197 | Adjusting indicator gauge on integral power tilt & trim | 8/78 |
| Evinrude 1198 | Integral tilt & trim stuck in tilted position | 8/78 |
| Evinrude 1200 | Vertical elevating devices for outboard motors | 8/78 |
| Evinrude 1201 | Hydraulic tilt & trim check valve corrosion and repair kit p/n 173569 | 9/78 |
| Evinrude 1202 | — Separation of integral tilt & trim check valves | 9/78 |
| Evinrude 1190 | Voltage regulator kit p/n 173573 (revised) | 10/78 |
| Johnson 1486 |
Frahm Resonant Reed tachometer |
12/78 |
| Evinrude 1210 | Reed tachometer accuracy and propping | 12/78 |
| Johnson 1489 |
Wiper nut for tilt tube steering on 1972 to
date - 70 thru V-6 |
1/79 |
| Evinrude 1214 | V-4 sensor adjustment with sensor gauge | 1/79 |
| Evinrude 1222 | Parts cleaning solvents and aerosol products | 5/79 |
| Evinrude 1223 | Anti-siphon valves & fuel filter | 5/79 |
| Evinrude 1227 | Integral TNT replacement relief valve o-ring | 7/79 |
| Evinrude 1236 | Commercial use of larger outboard motors | 10/79 |
| Johnson 1511 |
Install trail lock spring with power
"tilt kit" on 1980 3 cyl. & V-4's |
12/79 |
| Johnson 1512 |
Control knobs for accessory remote controls |
12/79 |
| Evinrude 1239 | Evinrude - — Adding trailing lock spring p/n 323142 | 12/79 |
| Evinrude 1240 | Control knob service kits for OMC acc. remote control | 12/79 |
| Johnson 1522 |
Selecting correct 5 or 6 pulse tachometer
for - 6 thru V-6 |
3/80 |
| Johnson 1524 |
Fuel line vacuum tester on V-4's & V-6's
to date |
3/80 |
| Evinrude 1246 | Evinrude - — Steering handle kits | 3/80 |
| Evinrude 1248 | Evinrude - OMC tachometers | 3/80 |
| Johnson 1526 |
Handle cover kits for accessory controls |
4/80 |
| Johnson 1531 |
High reading temp gauge and ammeter -
Battery overcharge on 1978 thru 1980 - V-4's & V-6's |
4/80 |
| Evinrude 1251 | Remote control handle cover kit p/n 173742 | 4/80 |
| Evinrude 1252 | Evinrude - Fuel line vacuum tester special tool p/n 390954 | 4/80 |
| Johnson 1536 |
Modification to T-N-T stand will allow bench
testing after repair |
5/80 |
| Evinrude 1260 | Evinrude - Power tilt and trim stand p/n 390008 | 5/80 |
| |
|
|
| MISCELLANEOUS |
| Bulletin
# |
Subject |
Date |
| Johnson 1264 |
Identifying
improved lift bracket on 1969 thru 1971 - V-4's |
6/71 |
| Johnson 1293 |
Safety and
warning symbols |
6/72 |
| Evinrude 1004 | ‘ Tank testing 1973 50 - 135 hp motors | 2/73 |
| Johnson 1323 |
Starting engines
at speed on 1974 to date - 50 thru V-6 |
10/73 |
| Johnson 1326 |
Ignition key
blanks for 1973 to date - All electric start models |
10/73 |
| Johnson 1332 |
Defective pivot
screw on 1973 & 1974 - 65 thru V-4 with accessory T-N-T and 1974 - 115
& 135 with trim |
1/74 |
| Evinrude 1033 | Recordak Easamatic reader service | 1/74 |
| Evinrude 1041 | Service tips 1974 9.9 & 15 hp models | 4/74 |
| Johnson 1348 |
Maintenance in
adverse conditions all models to date |
5/74 |
| Johnson 1351 |
Hard starting on
1972 & 1973 - 50 |
8/74 |
| Evinrude 1055 | Repair kits for 1974 9.9 and 15 hp engines | 8/74 |
| Evinrude 1064 | Electric motor service tips | 11/74 |
| Evinrude 1093 | 1975 70 hp engines with incorrect identification plates | 7/75 |
| Evinrude 1094 | Mixed stock - thrust bearing 378262 | 8/75 |
| Johnson 1385
Rev. 1 |
Recommended fuels
1 1/2 thru V-6 to date |
9/75 |
| Johnson 1390 |
Lifting engine
and removing from carton on 1976 to date V-6's |
9/75 |
| Evinrude 1116 | Steering system, fuel system and drywell drain hole recommendations for all single or dual engine installations totaling 150 hp or more | 2/76 |
| Evinrude 1123 | New bushing p/n 387618 for EB12S and EB14S electric outboards | 4/76 |
| Evinrude 1132 | Micro Design Microfiche reader service | 7/76 |
| Evinrude 1133 | Amplifier & pulse pack for 1972 models | 7/76 |
| Evinrude 1138 | Changes in 1977 Evinrude outboards | 8/76 |
| Evinrude 1153 | 9.9 - 15 hp reverse thrust kit - test prop RPM | 6/77 |
| Evinrude 1155 | Corrections to 1977 Master Parts Price Book | 7/77 |
| Evinrude 1188 | Land and Sea Performance Center ‘‘Evinrude 255” | 5/78 |
| Evinrude 1194 | Emergency engine cooling using trouble cooler | 6/78 |
| Evinrude 1195 | Amplifier & pulse pack for 1972 models | 6/78 |
| Evinrude 1196 | Application of motor decals | 6/78 |
| Johnson 1474 |
Application of
decals on all models to date |
7/78 |
| Johnson 1490 |
Corrections to
1979 Service Manuals - 6 thru V-6 |
2/79 |
| Johnson 1496 |
Engine failure
due to improper break in procedure on 1979 to date - V-6's |
6/79 |
| Johnson 1500 |
Use of parts
cleaning solvents and aerosol products |
6/79 |
| Evinrude 1224 | Necessary break-in recommendations | 6/79 |
| Evinrude 1231 | Commercial use of larger outboard motors | 8/79 |
| Evinrude 1234 | 1978 55 hp Parts Catalog error | 10/79 |
| Evinrude 1237 | Evinrude - 1980 4.5/7.5 hp Parts Catalog omission | 12/79 |
| Evinrude 1238 | Evinrude - Micron Corporation - Microfiche reader service | 12/79 |
|
|
|